Jump to content
SAU Community

R32 Diff Question

mark32gts-t
 Share

Recommended Posts

mark32gts-t Collaborator

mark32gts-t

Posted
Posted

My diff whines like hell and am considering just replacing the whole housing with a 2nd hand one. My question is this, my car has ABS and from what I understand it has an ABS sensor in it. Can this sensor be transferred across into a non ABS housing. I had a look on fast and there appears to be an illustration showing the sensor. Just not sure if the ABS section can be fitted into a non-abs diff housing. Included the fast image. Any help would be much appreciated. Cheers

LSD.jpg

Link to comment
https://www.sau.com.au/forums/topic/231873-r32-diff-question/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

First off, do you have oil in the diff? Do you have enough oil in the diff? Do you have new oil in the diff?

Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted
First off, do you have oil in the diff? Do you have enough oil in the diff? Do you have new oil in the diff?

Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

yes, diff oil has been replaced and is filled to the correct level. it only whines on deceleration, from what i've read its the meshing of the gears that have "play" due to wear and this is what whines... anyone else???

bubba Grand Master

bubba

Posted
Posted
Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

Yes that is where the ABS sensors are, my Nismo diff came with new output shafts/flanges and they had the ABS sensors on them (my car doesn't have ABS).

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted

Just thought I'd upload some pics of where the ABS sensor is located, for reference sake. Its on the tailshaft input and not on the driveshaft outputs. The sensor bolts into the actual housing so unless the non-abs diff has the hole blocked off I dont think its as easy as just swapping the sensor over. Thanks to the people who responded anyways. pics:

ABSSemsor1.jpg

ABSSensor.jpg

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted

I think it would be possible to swap the internals over. But I dont really have time to be doing it right now.If I have to swap stuff over I may as well do what 'White GTS-T' said and buy a two way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • MBS206
      The Cool Tools Thread

      By MBS206 · Posted

      I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
    • GTSBoy
      SR20 to cefiro

      By GTSBoy · Posted

      I would suggest equally difficult to find, perhaps edging to the SR. Turkey has almost exclusively Euro market cars, some Korean, few Japanese other than pedestrian shite. I guess they're probably losing the fight against Chinese shit like we are now too. I would vote for a BMW V8, found in a 540i in a wrecking yard somewhere in Deutschland (or possibly Albania).
×
×
  • Create New...