Jump to content
SAU Community

Cant Select Gear After Clutch Change! Help

battery
 Share

Recommended Posts

battery Mentor

battery

Posted
Posted

so i changed my clutch, pressure plate,thrust bearing and spigot bush this weekend and put a different flywheel on too.

now i still have the car on the stands but when i have the engine running it wont let me put the car in to gear, its like the clutch isn't engaging?

i had a look under the car while somebody pressed the clutch and the fork seems to be moving fine.... i have not bled the system but theres defiantly pressure in the pedal.

its the first time i have done a clutch so im not 100% if i put the thrust bearing in correctly has anyone got any pics of how it should be.

any ideas i really don't want to pull the bloody thing out again!

BHDave Grand Master

BHDave

Posted
Posted (edited)

if you haven't disconnected the slave cylinder then there's no reason you'd need to bleed the fluid to make it work.

The ABS light has nothing to do with clutch operation. It may be because the wheels are off the ground.

Climb under the car, take the slave off the box and check that the fork is attached properly. Pull the boot off and get a torch and make sure when you move the fork around the carrier is moving properly. Chuck the slave back on and get a mate to push the pedal while you are watching the carrier and see if it is engaging.

If it all seems to be working properly you may just need to adjust the clutch at the pedal to get a bit more travel.

Edited by BHDave
battery Mentor

battery

Posted
  • Author
Posted

pulled the box off again, found a few small bits of the new spigot in the pressure plate, im fairly sure i needed to push it in a bit so ill get a new one tomorrow and try again!

how far in should it be? i had it about 2-4mm out of the hole should it be flush or right to the back of the hole?

BHDave Grand Master

BHDave

Posted
Posted
pulled the box off again, found a few small bits of the new spigot in the pressure plate, im fairly sure i needed to push it in a bit so ill get a new one tomorrow and try again!

how far in should it be? i had it about 2-4mm out of the hole should it be flush or right to the back of the hole?

it should be about 4mm in

zonbie Explorer

zonbie

Posted
Posted

For the clutch not to be working, (not disengaging when clutch pedal depressed) it sounds like the spigot bearing/bush is jammed onto the input shaft.

When you get a new bearing'bush, triple check your input shaft diameter with the inside diameter of the bush.

It appears you currently have a mis-matched set.

battery Mentor

battery

Posted
  • Author
Posted

so i changed the spigot, it is now perfect im 100% sure this time.

but still couldn't select gears!!!!

so put a washer in between pivot ball and fork to get the thurst bearing closer to plate, it worked briefly then i guess the washer flattened out, it was a cone type.

problem is the slave was bottomed out when clutch pedal was out so im guessing this will make the clutch slip due to the thurst bearing still being against the pressure plate. agreed?

im out of ideas, gonna take it to a workshop i think!

battery Mentor

battery

Posted
  • Author
Posted

been at the workshop a few days now they still haven't figured it out.... im thinking it must be something to do with the thickness difference between the old and new flywheel/clutch/pressure plate combos....

it works when i lever it with a screwdriver so im fairly sure its not stuck in the spigot, it could be a bent clutch i guess which it explains why it needs so much movement to disengage....

then again people say the fork should be at 90 degrees to the box when disengaged mine is about 60...... but im getting a good 15mm movement from the slave.

it will work if i use a bigger slave rod or put washers behind the pivot point but then the clutch will never full engage because the slave bottoms out.

anyone got any ideas?

blind_elk Grand Master

blind_elk

Posted
Posted

Have you checked the "socket" of the thrust fork, where it pivots on the ball, for signs of cracking? If there is cracking, the cracks simply open up when you press the clutch pedal, and the thrust bearing doesn't push the pressure plate.

Did you measure the height of the clutch / flywheel assembly and compare it to what you took out?

battery Mentor

battery

Posted
  • Author
Posted
Have you checked the "socket" of the thrust fork, where it pivots on the ball, for signs of cracking? If there is cracking, the cracks simply open up when you press the clutch pedal, and the thrust bearing doesn't push the pressure plate.

Did you measure the height of the clutch / flywheel assembly and compare it to what you took out?

doubt its cracked, but will check.

i didn't measure the difference, this seems to be the only explanation!

battery Mentor

battery

Posted
  • Author
Posted (edited)

alright so apparently the new kit is about 10mm difference in length.

the workshop reckons the r32 has two different sizes of flywheels and i must have got the wrong kit?

the car had a manual conversion at some stage and i have no idea what box/clutch/pressure plate/flywheel they put in it may not even be from a skyline .

anyway the workshop is gonna suss it out!

Edited by battery
FTO Enthusiast

FTO

Posted
Posted
fixed was the wrong kit its got a 225mm kit on there now which has a part number completely difference to any skyline!

Weird..should be 240mm. What's the part number on the kit.

Anyone have squealing noise from a rear main seal after installation (pre lubed)

it's aftermarket, so wondering if it's slightly undersized.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...