Jump to content
SAU Community

Can I Remove This Distribution Block Between The Master Cylinder And Slave Cylinder? - R32 Gtst

Shaun
 Share

Recommended Posts

bubba Grand Master

bubba

Posted
Posted

I whacked a braided line in on the weekend (old rubber hose was weeping where it went into the slave cylinder), binned the distribution block and the cooler pipe. Clutch feels a LOT nicer now, not heavier or lighter but feels somewhat more "direct" if that makes sense :P

ellie Proficient

ellie

Posted
Posted

Can't help but wonder why the factory saw fit to have it there in the first place. I think there is sound logic to upgrading things but the engineers that designed such a fantastic car with great longevity are no idiots. Has anyone actually pulled the cooler distribution box apart before? The pipe which the factory use is relatively easy to work also, so, maybe the block can be taken out and replaced with a short finned section like on the P/S cooler on GTRs? Obviously replacing the short rubber hose with braided.

Just food for thought anyways. . . .

Abo Bob Grand Master

Abo Bob

Posted
Posted

They do it to make the car smoother which has the effect of reducing the feel. We don't mind the harshness cos we want the raw feel. Same reason they put soft suspension and sound deadening in there. They take the NVH out and we spend years putting it back in! :P

ellie Proficient

ellie

Posted
Posted

That is a valid point you make! They would make the system with Tom,Dick and Harry in mind. And I am actually about to replace mine mainly because of the whole new world that braided brake lines opened up to me. It was a major improvement and I can only imagine the clutch should have similar improvement with engaugement feedback. :D

  • 8 years later...
jjcb Contributor

jjcb

Posted
Posted

Hey everyone,

 

Sorry to dig up an old tread but I'm in the process of changing my clutch line (R32 gtr). From the master direct to the slave. Just want to know what happens to the connection to that distribution box? (Where it originally went from master to the distribution box). Do you just leave it or put a bolt in there?

 

Thanks in advance!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      RB26 turbo oil banjo bolts

      By sunsetR33 · Posted

      No no, sorry I think I made you misunderstand. I have this Tee as well as the lines that go from there. What I am missing is the banjo bolt that connects this line (OEM turbo oil supply line) To this hole, this line is mounted on the turbo and reaches around it so you have easy access the oil and water supply being rerouted to this dual banjo port in the front. like this
    • sunsetR33
      RB26 turbo oil banjo bolts

      By sunsetR33 · Posted

      Nothing at the moment as previously there was a crappy braided line going from engine block directly to the turbo. I have bought a used OEM hardline for the turbo oil supply, which goes from the engine block to the marked hole. I don't have any of the OEM banjo bolts for oil except the one at the block.
    • GTSBoy
      RB26 turbo oil banjo bolts

      By GTSBoy · Posted

      This is the tee No specs on the page I grabbed it from, out of stock there anyway. But it kinda looks like a 1mm pitch. Would not think it's going to be 0.75mm pitch.
    • GTSBoy
      RB26 turbo oil banjo bolts

      By GTSBoy · Posted

      See above.
    • GTSBoy
      RB26 turbo oil banjo bolts

      By GTSBoy · Posted

      OK, I'm with you now. The outlet of the tee that is banjo'd into the block. Dunno what it is, will have a scratch around. The M11 question is.....messy. The minor diameter of an M11x1.0 male thread is 9.917mm. This is smaller than the minor diameter of a 7/16"-24 UNS (which is 10.08mm). The M11 major is 11mm. That's smaller than the major on a 7/16"-24 UNS (which is 0.4375" or 11.1mm) so an M11x1 bolt should pass on the major side. The pitch of a -24 thread is 1.058mm, which is really close to the M11x1, so it should go in at least several turns. I would expect M11x1 to be loose in a 7/16"-24 UNS, at least until enough thread are engaged to make it stop screwing in, if that can happen. Probably wouldn't happen on such a short bolt as you're looking at on the oil tee. Keep in mind that 7/16"-24 is NOT a standard/typical 7/16" thread. Standard is 20. That's the UNF or fine thread. -24 is really fine. I imagine that Garrett chose -24 for the turbo housing oil inlet to get the number of threads engaged up. I would not expect Nissan to have an imperial (UNF, etc) thread on that tee. I would expect it to be metric (if it is a bolt thread) or BSP (actually the Japanese equivalent of BSP) if it is a pipe thread. Given that it's a banjo, it's going to be a bolt thread. If it looks like an 11mm will go in there, then 11mm seems likely. It is very possible that some clown has stuffed that thread by trying to jam some imperial "near equivalent" into it, perhaps with those hoses of yours. Got verniers? Measure up the threads on the hoses.
×
×
  • Create New...