Jump to content
SAU Community

Er34 - Fuel Pump?

lcy

By lcy,
in Engines & Forced Induction

 Share

Recommended Posts

lcy Rising Star

lcy

Posted
Posted

Hi ppl.

i am going to replace my stock fuel pump with the bosch 040 fuel pump.

the problem is that most ppl had done r32 and r33 but the r34 is alot different than the both....

http://www.skylinesaustralia.com/forums/In...bosch+fuel+pump

looking at this previous post. nothing is similar to what i have in my r34 gtt.

instead of unscrewing the cradle which is connected to the fuel pump, mine is like a screw type cover (which i am having difficulty removing). and the position of the fuel pump is near the end of the boot instead of the boot(towards the back seat).

any one have any idea if the fuel fump installation will be the same as the r33 and r32?

many thanks in advance.

cheers!

Link to comment
https://www.sau.com.au/forums/topic/233688-er34-fuel-pump/
Share on other sites
DECIM8 Grand Master

DECIM8

Posted
Posted

What are you on about?

Installation is same a R33.. unbolt cover which is in the boot right hand side of the shelf/lifted part of the boot behind the rear seat.

Use a hammer and peice of wood to "undo" the fuel tank lid it takes awhile.

Pull the pump wires out + hoses.

Pull out pump by pulling up toward you if your having trouble finding it.. it is located about 20cm inside the tank on the wall closest to the rear seat.

Replace and ur pumping away.

Link to comment
https://www.sau.com.au/forums/topic/233688-er34-fuel-pump/#findComment-4096693
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rebuilt Rb25det issues

      By GTSBoy · Posted

      Use a 2' length of hose (that's 2 foot, not 2 inches) as a stethoscope to localise the source of the ticking. From cam covers? From exhaust or turbo manifold gasket? From injectors? From lower down in the engine? Etc. Use a timing light to set the timing. Put Redline Lightweight Shockproof in the box. It's not the very best thing for the box, but it will take a box that refuses to engage a gear with other oil, and make it engage a gear. I had to put it in when I installed the R33 box I have in my car. It would not select ANY gear when running. Smurf jizz made it work. That was >10 years ago and I still use it. I'm stuck with it now. Failing that - rebuild the box.
    • Victory
      Neil's R33 Gts-t Build

      By Victory · Posted

      Well done Duncan. The fuel tank bulkhead lid is also in great condition (some of mine were stuffed). These are now out of production and good ones like that are becoming hard to come by.
    • Milkmun
      S15 Spec R

      By Milkmun · Posted

      Wow that's a steal, you've done well there. 
    • trey318
      r34 gtt led globes

      By trey318 · Posted

      Exterior LEDs R34 2Dr R34 4Dr Position Lamp T10 T10 Winker front T20S T20S side T10 T10 rear T20S S25S150 Anti-hyfla relay TYPE3 TYPE3 tail T10 T20W Stop Lamps T20W T20W High Mount T16 T16 back T16 T20S number T10 T10 trunk T10 T10 Interior LED Item No.     Map Lamp BA9S single-sided     Room Lamps T10×31     Trunk Lamp T10     meter Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     Liquid crystal section T6.5 pedestal     Winker T6.5 pedestal     High Beam T6.5 pedestal     3 SERIES METER Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     air conditioner Early Liquid Crystal T3     Late LCD T4.2 Short     button T4.2 Middle     Hazard SW T3 Pedestal Short     Keyring T5     Cigar Socket T5
    • KyoyaR33
      Rebuilt Rb25det issues

      By KyoyaR33 · Posted

      Howdy all,   I had my rb25det S2 rebuilt and finally started it today but have run into a few issues  Engine sounds like a a diesel easiest way to summarise like small ticking, gets louder when revs are slightly adjusted  The engine builder repainted the engine cover leaving no where for me to go off with lining up the CAS so have it as central as possible so not sure it that could be affecting it?, changed the gearbox fluid too but won’t seem to go into gear when running, and only 1 to 4 when off having a hard time finding 5th and reverse anyone got any ideas or a base for me to start off? much appreciated 
×
×
  • Create New...