Jump to content
SAU Community

Rb26 Into S13 Silvia

Proximity Motorsport
 Share

Recommended Posts

Butters Experienced

Butters

Posted
Posted

Hi,

Just thought I might share some more RB26 into S13 insight. When I got my sump converted I got them to add on an extension. Holds a fair bit more oil now.

Also got a custom sway bar made by the selby guys. Its the right shape but they made it sit way way too low. I have to send it back to get it re-done.

See pic -->

SwayBarNSump.jpg

Don Dada Mentor

Don Dada

Posted
Posted
heres a pic of mine that went into a cefiro used rb20 engine mounts and had the sump modded

It did not look like u had to modify the sump to clear the sway bar... correct???

However it looks pretty close,probably from the angle of the pic. How much clearance is there between them?

Rb 20/25 mounts are the same right? That is the rectangle mount one bolt on top and one underneath.

STATUS Grand Master

STATUS

Posted
Posted
It did not look like u had to modify the sump to clear the sway bar... correct???

However it looks pretty close,probably from the angle of the pic. How much clearance is there between them?

Rb 20/25 mounts are the same right? That is the rectangle mount one bolt on top and one underneath.

Any car that comes with a RB series engine does not need the sway bar mod.

  • 2 weeks later...
Don Dada Mentor

Don Dada

Posted
Posted

post-42272-1241741442_thumb.jpg post-42272-1241741657_thumb.jpg

Just thought i'll update as to what had to be done for the 26 sump to fit in the C35.

One problem i've come across though is the power steerin pump..... the high pressure line does not line up.

What have u guys done???

Use the 25 pump???

Does the pulleys line up using the 25 pump or do i need to change the bracket as well???

I also noticed the 26 pump uses a slightly thicker belt, if i use the 25 pump what belt would work to mesh the groove on the balancer with the thinner 25 pump groove???

Butters Experienced

Butters

Posted
Posted
One problem i've come across though is the power steerin pump..... the high pressure line does not line up.

Use the power steering pump from the RB26. Get a custom power steering line made.

You can just see in the below pic the custom line and swivel setup coming up to the PS pump.

Should cost you around $100 ish to get done.

vq33_006s.jpg

Butters Experienced

Butters

Posted
Posted

Also notes on mounts. I found the RB25 mounts different to rb20, although been told they were the same. So something weird there.

I used the rb20 ones. A note on that, if you use the rb20 mounts the oil filter will be dangerously close to the mount. Make you modify it

to clear. Seen two cefiro's split the filters and lose there oil due to this.

STATUS Grand Master

STATUS

Posted
Posted
Hi,

Just thought I might share some more RB26 into S13 insight. When I got my sump converted I got them to add on an extension. Holds a fair bit more oil now.

Also got a custom sway bar made by the selby guys. Its the right shape but they made it sit way way too low. I have to send it back to get it re-done.

See pic -->

SwayBarNSump.jpg

Should have extended the other side, the side you have modified is less effective than before except it holds a smidge more.

Butters Experienced

Butters

Posted
Posted
Should have extended the other side, the side you have modified is less effective than before except it holds a smidge more.

Holds quite a bit more actually. Around 500-600ml more then a standard sump.

I will admint it would have been nice to extend the other side.

Not sure what you mean by "less effective then before" .... ?

a31lunacy Proficient

a31lunacy

Posted
Posted

i used an rb25 oil filter block (the one that mounts to the engine block) and am running a oil cooler kit so i clear sweet as. and yes should mod both sides because the mod you have performed only removes the small walls that were there previously in the stock box section i gained an extra 1.5 lt (inc the oil cooler) and for the price a tomei sump baffle is a great idea.

STATUS Grand Master

STATUS

Posted
Posted
i used an rb25 oil filter block (the one that mounts to the engine block) and am running a oil cooler kit so i clear sweet as. and yes should mod both sides because the mod you have performed only removes the small walls that were there previously in the stock box section i gained an extra 1.5 lt (inc the oil cooler) and for the price a tomei sump baffle is a great idea.

yep and those walls or chambers are very useful.

  • 2 years later...
wolverine Grand Master

wolverine

Posted
Posted

The stagea AWD blocks have 2WD sump holes but the oil pickup location is different and this can mean you will need to massage a 2WD sump to clear around the pickup. The 2nd set of holes is slightly inboard.

You will need to modify the oil pickup angle which means cutting, die grinding out the bracket and brazing it to the correct angle to suit the 2WD sump and trim some of the baffle.

  • 2 weeks later...
N1 RB26 Contributor

N1 RB26

Posted
Posted

sorry got a quick question is there any benefit to mod the gtr sump? why not just get a rwd sump that will fit that's already got enlarged volume baffles doors etc. cause i'm doing a 26 into a gtst and get a pan to fit that holds 9L baffles, doors, and mesh windage for $700 or should i mod the gtr sump instead? just seems like a lot of stuffing around that's all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Hope the cans went down well at least 
    • Milkmun
      Neil's R33 Gts-t Build

      By Milkmun · Posted

      255 can't go wrong with the price.
    • Kinkstaah
      Neil's R33 Gts-t Build

      By Kinkstaah · Posted

      When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...