Jump to content
SAU Community

Recommended Posts

just drive normally and youll be fine

you will only have troulbe if you load the engine up

the std service manual tells you specs for snow chains and how to fit them

id strongly advise getting a normal car for the snow however

Thanks all, I was at Hotham a couple of weeks back when it was snowing heavily and the roads were closed, but I had a mitsubushi outlander and it was a piece of piss to drive in the snow (slow speeds). Im not out to break any mountian climb records but thought it might be a nice drive and save me hiring a car again.

There is now much more variety of snow chains available with scratch protectors etc but Im keen to know if anyone has fitted any chains to their R32 GTR and wether its front or back wheels, and wether they foul on the wheel arch liner?

Cheers, Sandy.

not as obvious as you might think, lotsa new 4wds advise chains on the front wheels, is good to combat understeer aswell as traction issues, admittedly they also drive mainly from the front. Id like to know what nissan reccomend for the GTR.

Sandy

You're pacifically asking about the 32 are you?

I went up to Lake Mountain a few weeks back in my R33 GTST. There wasnt much snow on the road as most was ploughed off, it was still very slippery though. If the road is like that you should be fine without chains, just drive slow and off boost.

I went up to Lake Mountain a few weeks back in my R33 GTST. There wasnt much snow on the road as most was ploughed off, it was still very slippery though. If the road is like that you should be fine without chains, just drive slow and off boost.

Lake mt to Hotham is like Mt Buller compare to Niseko Japan! I took my old 33gtst to Buller along time ago, the car is fine, just drive within your limit.

Could be a bit of overkil with chains on all 4 wheels (have to hire and fit em), does anyone know what nissan recommend for the R32 GTR?

Why dont' you ring up NISSAN themself?

Though it sounds like alot of fun, still, taking a GTR to the snow isn't the best idea as you'd imagine the Attessa System will be working over-time for sure.

unless you absoloutely had to i wouldnt do it. GT'R is about the last car i'd want to take up to the snow. heavy on fuel, bugger all room for bags, bugger all room for people inside without it turning into a fogged up sauna, and i can only imagine it would wreak havoc on the attessa system - wouldnt know what was going on!

Lake mt to Hotham is like Mt Buller compare to Niseko Japan! I took my old 33gtst to Buller along time ago, the car is fine, just drive within your limit.

Niseko?

Haha. I really havent been to Hotham or Buller before so I have no idea what either was like.

Just put chains on the rear wheels and take it easy. Stay in Second whenever you're on the snow/ice - even when taking off.

As soon as you've driven the first 10m with chains you'll know what you're dealing with.

I just bought some Konig chains for this season - if you get the correct size they won't scratch your rims (they barely touch them).

One thing to note however is the clearance from guards/suspension, if the car is excessively lowered or has extra wide rims forget it.

Just put chains on the rear wheels and take it easy. Stay in Second whenever you're on the snow/ice - even when taking off.

As soon as you've driven the first 10m with chains you'll know what you're dealing with.

I just bought some Konig chains for this season - if you get the correct size they won't scratch your rims (they barely touch them).

One thing to note however is the clearance from guards/suspension, if the car is excessively lowered or has extra wide rims forget it.

PS. Chains are very important - just ask this guy (up to Mt Baw Baw 17/08/08)

post-2652-1221220278_thumb.jpg

i went to bullar in my s2 stagea ... no worries didnt even bother with chains .. no slip at all .. plus the traffic i was behind, i was doin a max of about 30k's up and down ... so i dont see any reason too .. just to save money and time and have a smooth ride now a ride that feel's like you have flat tyers driving over bricks :O

I've driven the back roads from Lake Mountain to Reefton in an R31 two years ago whilst snowing

with no chains. No the most pleasant experience.

Simply kept the car in 1 and/or 2nd gear (auto) and keep the speed at 20km or less with no sudden acceleration to cause the tail to kick out or put you into an aquaplain, also or no sudden decelelarion (compression lockup) to have the tail kick out.

Same with the steering, no sudden turns, keep it smooth.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
×
×
  • Create New...