Jump to content
SAU Community

Recommended Posts

so these will change the lower light in the headlight.. the one which doubles as the fog lights? i managed to not have my normal driving lights changed during compliance but the light below (Fog Light/highbeam) are abit yellowish in comparison

Link to comment
https://www.sau.com.au/forums/topic/235261-piaa-h4-globes/#findComment-4121426
Share on other sites

so these will change the lower light in the headlight.. the one which doubles as the fog lights? i managed to not have my normal driving lights changed during compliance but the light below (Fog Light/highbeam) are abit yellowish in comparison

ok, For my car, The normal low beam should have a D2R HIDs on it but due to compliance, they change it to a H1 normal halogen bulb. As for the high beam, it's the original H4. If you on the high beam, both the high/low on the H4 will light up. If you have the lower light with the fog light option, Good. For me, nothing turns on when I switch on the fog lights. These PIAA bulbs are original PIAA from Japan. I manage to get them cheap, therefore I can offer them to you cheap too. it's easy more than AUD100 selling outside.

Link to comment
https://www.sau.com.au/forums/topic/235261-piaa-h4-globes/#findComment-4122742
Share on other sites

On this note, how exactly do you replace the bulbs? I had a quick look the other day (admittedly in poor light with a torch) and I couldn't see where the bulbs plug in. In fact, I'm not sure there was any space to put a hand in behind the lights. Do you have to remove bits to get at the lights?

Link to comment
https://www.sau.com.au/forums/topic/235261-piaa-h4-globes/#findComment-4124315
Share on other sites

if sedan - raise car off ground. pull off front wheels pull inner guards loose and there ya go.

if coupe - remove front bar then remove headlight assy.

Hei Chris, you have not reply my massage. So what'z going on? Can you still help me?

Link to comment
https://www.sau.com.au/forums/topic/235261-piaa-h4-globes/#findComment-4129650
Share on other sites

with your fog lights - pop the cover off the back of the stalk and plug them back in.

regarding the airbag light. no - the fellow is away for a few weeks.

Hi Chris,

I manage to take out the light stalk, but I didn't find anything amiss. The wire is intact connected. Can you fix it for me when you the the airbag reset thing.

post-53067-1221472094_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/235261-piaa-h4-globes/#findComment-4134205
Share on other sites

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did a conversion on my rb20 with rb25 cam and pulley, controlled it with a solenoid (forgot the port diameter of the solenoid)  and made an oil port on the cam cap to lower pressure in the journal. Difference  is day and night, the rb20 isn't dogshit down low anymore, not a powerhouse but this had add much welcomed torque down low. Boost build a bit sooner and torque rise way more when it start building boost. Only need to deactivate the VTC past 6500/7000rpm.   Knowing how it help with only 2L, having it on 2.6L it should be a mod to think about early on as it gives a lot of performance on most on the rev range.
    • https://www.nengun.com/hks/valcon-rb26-v-cam-system   no controller but most will use ECU to control anyhow
    • Not too sure, the throttle body has 4separate plugs going to it. Im not sure if the throttle is driven by cable and the motor is for traction, cruise and something there light blue one is TPS. i don't understand why the throttle won't open with the cable until about 3/4 on them only moves the valves very slightly
    • There are other crowds doing 25Neo conversion kits.
×
×
  • Create New...