Jump to content
SAU Community

Rb25det/rb30 Engine, Need Advice

Stagea Denmark

By Stagea Denmark,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Stagea Denmark Collaborator

Stagea Denmark

Posted
Posted (edited)

Hi Guys.

I need some advice to find parts for my new engine.

I got 2 RB30DET engines from Australia, and have searched the internet to find rods, pistons ect., good enough to make more then 800AWHP, Tomie rods and pistons is rated to max. 750, whats better and stronger, i have 2 RB25DET engines, and one of these will be the top on this engine, right now i have a guy and he taking good care of this top, and porte is, the inlet looks fine, but there is a bigger job on the exhaust site.

Setup will be a big single turbo, a GT42R, i have the R34 gearboks, have a guy who will build new axels, he normally build to tractor-pulling :-)

This will be a everyday car, and for some fun in the weekends at the dragstrip, i know i will get lag, but thats fine.

Car is a Nissan Stagea RS-Four V

Where will my limits be, what to be wear of, don´t know anything about this RB30 bottom, have bouild many 2JZ-GTE and RB25DET engines, but never this one.

Have found a lot treats here, but not with the same goal as i have.

So far i have found:

Cams Tomie Pro 260 in/ex - 10.25. + lifters.

Bearings and gaskets.

Waterpump

Oilpump

Edited by Stagea Denmark
Link to comment
https://www.sau.com.au/forums/topic/235894-rb25detrb30-engine-need-advice/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...