Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

I only just solved a shocking miss and sputtering above 3k rpm that had been getting steadily worse. But it was totally intermittent, the car would drive fine for long periods then just come to a sputtering halt in 30 seconds flat.

Determined to find the problem i changed the plugs, no go

I took it to my local speed shop and they told me i had the wrong plugs in and wrong gap. Stick new ones in... no go

For some reason my suspicion was that it wasnt ignition. Because when i stick it in a high gear at low speed (give it some high ignition load) it would just pull out. Then splutter again at a bout 3200rpm, then pull smooth to redline. Other times it would break down so much it wouldnt pull past 2000rpm.

The solution? Air flow meter. Pull it out and give it a good spraying of contact cleaner. Car now drives better than ever.

Red17

I am not the best person to answer this queston as I have not had a dyno run with my skyline yet and am south east, I can however recommend Hypertech Autosports

7 Trade Place Vermont VIC 3133 (03) 9874 8866 Ask for Arnold

  • 2 weeks later...

Just out of interest When I started my car this morning when it was cold it started to idle roughly again, so I unpluged the AFM and the revs went up but the car ran beautifuly. whats got me that my Auto elec said they had it tested & calibrated it and it was fine, I have my doubts. now to find a loan one so I can test it...

Hi I had the same problem with my R34 it was missing like hell at about 4800 to 5000 revs.I replaced the plugs with Platinum and gapped them at 0.8.

I also suspected one of the coils might have been arking across to the cylinder head as well so I taped the stem of the coil pack with insulation tape,Hey presto going like a train no miss.

Maybe I should take the tape of the packs to see if it gets the miss back.

I had a very similar problem with a Telstra Ghia a few years ago.

So maybe worth a try.

WLD747

I had similar problems too you, changed and gapped plugs numerous times, coil packs checked, AFM, then raised the boost and it made it worse, backed it back and it was better. Then installed and dynoed tuned with a SAFC and fixed it. Basically for my car, it was getting to much fuel to drink. Are your plugs black?

And whilst not only fixing the problem, i scored some nice power gains.

I will be doing some further tuning soon.

http://www.skylinesaustralia.com/forums/sh...&threadid=22703

Robo's - thanks for the advise cause im getting a PFC asap which will enable me to tune my afr. I found out today from another mechanic that my car is extremely rich so yeh hopefully problem will disapear soon.

I recommend to anyone with mild mods to get a new ECU or a SAFC to balance the ECU. Because it makes sense. 1 -4RPM not much fuel so boost quick and hard then 4PRM + too much fuel and boogs down.

Thanks in advance Rob

AK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Last year I got a set of MCA street coilovers for my turbo Forester after my son hitting a concrete gutter/wall on a small bridge causing the whole drivers side suspension to get bent because the rain just made the car slide out I love them, I think they were $2400. even had a hiccup of have the wrong hub configuration (my fault) so got onto MCA and they sent the correct shock ends overnight parts from QLD, for free!  I was very impressed with their customer service and quality of the product  
    • They've had some weird failures on their brake actuators. One of them was because they added some kind of lubricant to the factory fill brake fluid that aftermarket brake fluid didn't have so it would affect the seals. Another was just mysterious, probably internal corrosion or something eating away at Prius brake actuators. Parts alone for those are a few thousand USD so not a cheap fix.
    • Selling a genuine Nissan Skyline R33 Coupe 8-Pin Power Window Master Switch Part No. 25401-26U10 Price $300   IMPUL Gear Knob – Rare JDM Upgrade Upgrade your interior with this genuine IMPUL gear knob – a rare and stylish addition to any JDM build. Premium quality, perfect fit, and an authentic Japanese touch for your ride.  Price:$300 Nissan Skyline R33 (Series 2) Sedan Tail Lights Immaculate Condition OEM JDM S2 a pair of OEM Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state. Price:$900   Located in Melbourne (Western Suburbs) – Shipping available Australia wide at buyer’s expense. DM if you need anymore details.  
    • KYBs are typically twin tube, putting them in the lower tier of desireability. Do you just want to replace worn out ones for the lowest cost? I mean, you wouldn't just replace one end of a car, if the rears are a similar age to the fronts, then they are probably nowhere near what they should be, and likely won't be great against brand new fronts. So, to spend ~$800 on 2nd tier dampers, when you could get a decent set of MCA coilovers for <$4k.....? As to the strut tops. 1st up, the Sparesbox site specifically tells you that they are not correct for an R33. Beyond that, why do you think you need them?
×
×
  • Create New...