Jump to content
SAU Community

Recommended Posts

as ive beign told the more holes the beter the atomisation wich will then cause beter ignition which will give more power and beter fuel economy. the less the holes the more dense the fuel and wont ignite properely and give worse fuel economy and pwoer. Sum1 feel free 2 correct me if im wrong.

havent seen any of them but logically it sounds about right.

1 big injection hole compared to 2 or 4 smaller holes seems like the fuel wont get burnt efficiently due to the fact it has a large clump of fuel coming from the one spot. whereas with the smaller more numerous holes, will have a more even spread and finer mist which in turn (im guessing) would give more combustion in the chamber?

god i pulled some technical sounding stuff out of my ass. but i think it sounds right?

IMO, for only 100 bucks more, i would get them.

Yeah i would get them.. I know a few people running rx7 injectors in their rb series engines because of the multiple jets for the mist effect rather than a single jet. As above more spread in the chamber = better efficiency and combustion.

Steve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey lads, reviving an old thread.  As an update, since the last time replied to this thread, ive done mostly suspension. Havent touched the motor except for maintenance. Though upon changing spark plugs, found out i had splitfires pre-installed! Updates: - Got me some stock airbox top cover and snorkel to fit onto the original intake. Should be free of defects - Bought a set of R34 GT-T brakes (not installed yet, going to rebuild + respray in champion blue + white 'Nissan' text) - Bought the last set of bilsteins from @Sydneykid and had them installed. Has been making some sounds on the rear but hopefully should be sorted out after this New Year break. - Regreased front caster rod bushings (poly bushes..) - Rear upper camber arms - Whiteline sway bars (BNF27Z 22mm + BNR11XXZ 24mm).  The rear sway bars are a bit short (ive read 50mm else where) but was still able to get them in.  Anyhows, I reckon suspension is sorted now. Maybe replace bushes (do have a set of front upper control arms from SK not installed yet) but should be okay for now. From now, I'm wanting to start working on the motor, drivetrain etc etc. Still debating on the order to go on and what to buy etc but: - ECU ( Haltech or Link ( Link states that it dont support A/T or AWD functions... Can anyone attest to this? ) - Highflow turbo ( ATR43ss2 ) - Intercooler ( Not decided yet, but cant find many good afoordable ones. Toshi says to opt for crossflow Japanese. Bit difficult this one, unless I get a returnflow Blitz from JJ? ) - Injectors ( Any recommendations ? I do have a nismo FPR ( Thanks SK ) ) - Seats - Tune by either Toshi or DVS To be fair, I did consider just keeping the stock turbo and nistuning it. Sat in a mates stock N, that had something like 200kw, and I reckon that felt more than enough. Maybe I should just go this route ahhaha. Too many choices.... Planning a trip down south, so wanting to just clean things up and make sure it gets to and from in one piece. Anything else specifically I should do before ? Cheers lads  
    • Must be for the car’s lucky charm 🤷🏽‍♂️ She runs fine, but it just seems to take about 1L less. Maybe I’ll have the oil sump dropped at some point to check if there is anything 
    • Hmmm interesting. Mine is the exact same and clearly the right one.  The mystery of the engine oil being full after 3.5-4L continues 
    • Yes I as well would like to find out where I could get some of the seat material with the red or blue small squares in it
×
×
  • Create New...