Jump to content
SAU Community

Recommended Posts

Make: R32

Model: 4 Door Automatic

Milage: 105000 (Just had 100k Service Done)

Transmission: Automatic

Colour: Black

Location: Caboolture

Complied? Yes

RWC supplied? Can Get one when required

Currently registered? Yes

Price: $9000 ono

Contact: 0488725030

Comments / Modifications: 3" turbo back exhuast, Pod Filter, and just the usual stereo etc.

Images: The Interior now has an alpine cd player but that is the only change

post-37740-1221558178_thumb.jpg

post-37740-1221558267_thumb.jpg

post-37740-1221558294_thumb.jpg

post-37740-1221559405_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/236317-r32-for-sale/
Share on other sites

I have owned it since import. ive been the only Aus owner the only thing i can say is bad is the fact the drivers side frot corner has had rock damage and has touch up spray paint on it :down:

Link to comment
https://www.sau.com.au/forums/topic/236317-r32-for-sale/#findComment-4136649
Share on other sites

Also would like to meantion that 10,000km ago i had the 100,000km service done

This included timing belt, new water pump, all oils changed etc

I also had a new 3" turbo back exhaust installed with 5" canon (i think its 5" anyways)

I also had the all 4 shock absorbers replaced aswell with KYB shocks

I also get all my services done at RPM Performance at Morayfield

if you have any questions at all send me a pm :)

Edited by Epyon
Link to comment
https://www.sau.com.au/forums/topic/236317-r32-for-sale/#findComment-4139156
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
×
×
  • Create New...