Jump to content
SAU Community

Recommended Posts

Hi guys,

Im new to the forum.

Im looking to upgrade my 32 GTR to between 300-330awkw.

I already rebuilt the motor because i bought it with a run bearing.

Here's a list of mods already done: ( i know now that half the stuff isnt needed, but i was young and silly. Anyway im working with these bits

N1 block

N1 crank (grubscrewed, linished etc)

cp pistons

Argo rods

ARP head studs

Race series bearings

Tomei MLS head gasket

Tomei sump baffle and oil restrictor

Tomei poncams 260/9.15

Tomei springs

Tomei adj gears

N1 oil and water pumps

Gates belt

Light port head

Tomei manifolds

Mines dumps

Bathurst spec turbos (i think)

full exhaust

Thicker intercooler

std afms

std injectors

Probably other things those are main ones for now.

Bathurst turbos quite laggy so im very interested in the GTSSs. Are they worth the extra dosh over the 2860-9?

Also what do you think they are capable of with my engine. (forgot to mention its running 9:1 comp)

What sort of boost do these turbos stop performing at?

Sounds like the go is nismo afms and 700cc injectors? does this sound about right?

Its a street car above all so looking to be responsive.

I appreciate any wisdom you would care to share (any silly questions i apologise for im a newbie)

Cheers

Luke

Edited by piranha

You've got SO many parts there needed for 400kw, so why not aim a bit higher?

I'd be putting a set of -5's on there (cheaper than gtss/-9 also), run them up to 24 psi.

You havnt mentioned ECU

Go get some "ID1000" injectors by a company called Injector Dynamics. Their drivability (eg street manners) is out of this world good.

Yes NISMO AFMs will do the job

Sell the current turbos, they're laggy and for that lag won't pay off with power.

Bathurst turbos quite laggy so im very interested in the GTSSs. Are they worth the extra dosh over the 2860-9?

Also what do you think they are capable of with my engine. (forgot to mention its running 9:1 comp)

What sort of boost do these turbos stop performing at?

Sounds like the go is nismo afms and 700cc injectors? does this sound about right?

If you want response then the -9s are the choice, no doubt, for a 2.6ltr. I had them on my GTR. Swapped em out for -5s and the car is noticeably slower below 150km/h, very noticeable delay in between gears. Which is the stuff you don't see on a dyno.

Above 150km/h-200km/h+ though obviously its a different ball game. So if you want response as in - under 150km/h performance - then -9s are the choice.

Sard 700s and Nismo AFMs will suit perfectly. Mine made 24psi early and then fell away to around 18psi in the top end, making 340rwkw @ 7000rpm (around 19-20psi), after that it drops off. They come on @ 3300rpm nicely however so plenty of range to choose from.

GT-SS & Garrett -9s are identical. The HKS items are a waste of money... Here is something I prepared earlier

http://www.skylinesaustralia.com/forums/topic/254450-79s-or-5s-garretts/page__st__440

You can get -9s locally for around $2800-$3000. That's complete with gaskets ($100) & actuators ($250).

If you paid $450 for 2 actuators, then you were stung yet again. They are $250 from GCG every day of the week.

The HKS Kit costs $300 more before it even leaves Japan. Add freight, add Tax... Even conservatively you've paid $3700

All for what?

A spray-on HKS logo on the 2 actuators. That's it. There is no other difference.

The HKS Kit is only comparative when the dollar was above 95, which when it was - the HKS kit was a good buy.

Thanks for the info nismoid

Will have to have a good think before I decide.

Sounds like the -9s would be a godsend after living with laggy bathurst turbos for a year.

Decisions decisions

. Mine made 24psi early and then fell away to around 18psi in the top end, making 340rwkw @ 7000rpm (around 19-20psi), after that it drops off. They come on @ 3300rpm nicely however so plenty of range to choose from.

You made 24psi at 3300rpm, or they started making decent boost at 3300rpm? Impressive if full boost from 3.3k and makes peak power at 7k, thats a 3.7k spread of useable torque, don't see any turbos on rb25s that make that kind of power spread at >=300kw

thanks for the quick reply N1gtr

Yeh I suppose I probably should aim a little higher.

Its got a power fc (afm version).

Also got gts4 diff gears

Will the nismo pump handle 400kw?

Diff gears done aswel? Ok forget -9. They're Just a terrible choice IMO given the rest of the setup.

Don't get caught up in the lag difference between -9 and -5, you're probably thinking it will be a lag monster and suck from reading the threads on here, given your gearing and the rest of the setup stick 5's on there and enjoy your car.

Pump should be fine.

Power fc will also be fine.

Btw Nismoids car on 9's was stupidly quick through hills, havnt been in it since his recent turbo swap, but will soon.

So it's not like 9's are crap, I'm not saying that, I'm trying to say you've spent about 10k in parts which pretty much all will be a waste on those turbos (stock rebuild in stock block will be fine for 9's).

Where are you located? You could always meet up with some built GTR owners and go for a ride or two before making the choice.

^ you know there is a difference. You've been in my car & saw it come on like a cut cat around 3500rpm in 2nd. :P

Will take you for a belt next time I drive up, or you come down. You'll see what i mean about in/out of gear stuff.

It's just what one person calls big vs another.

That extra half second delay in between gears from the larger -5s is the most noticeable between the two set-ups and kinda gives me the shits a little.

The RPM band you can just adjust driving style and pick a lower gear etc.

He is in NSW, i checked - otherwise I'd have offered myself lol :D

You made 24psi at 3300rpm, or they started making decent boost at 3300rpm? Impressive if full boost from 3.3k and makes peak power at 7k, thats a 3.7k spread of useable torque, don't see any turbos on rb25s that make that kind of power spread at >=300kw

No they start ramping up onto boost hard @ 3300rpm. Forget when it hit 24psi, I posted the graph(s) a while ago if it's a major concern.

Noticeably sooner than -5s either way.

-5s dont do much until 4000rpm but hold till 8000, my limit is set to 8300 and i hit it regularly so they still keep pulling.

Its pretty much the same power band to be honest. Its just a shift of 700rpm to the left really.

I never said anything about torque though... That progressively drops off, same as the -5s do.

Torque doesn't hold till redline.

You made 24psi at 3300rpm, or they started making decent boost at 3300rpm? Impressive if full boost from 3.3k and makes peak power at 7k, thats a 3.7k spread of useable torque, don't see any turbos on rb25s that make that kind of power spread at >=300kw

Well that's cause we aren't talking about RB25's in here

Eg mine on 5's (before bearing let go) did 150rwkw at 3000rpm, 235rwkw at 4000, then maxed the boost (ebc was off and was running off the pussy actuators). It was well on it's way to the same sort of number as before but was making something like 5psi from the start of the run at 1500rpm which is just incredible to drive.

Anyway, back to GTRs, maybe this guy needs to be posting in the 400kw thread ;)

No they start ramping up onto boost hard @ 3300rpm. Forget when it hit 24psi, I posted the graph(s) a while ago if it's a major concern.

Noticeably sooner than -5s either way.

-5s dont do much until 4000rpm but hold till 8000, my limit is set to 8300 and i hit it regularly so they still keep pulling.

Its pretty much the same power band to be honest. Its just a shift of 700rpm to the left really.

Cool thanks for that, a 4k power band is still impressive either way.

I never said anything about torque though... That progressively drops off, same as the -5s do.

Torque doesn't hold till redline.

No doubt, it always seems to in turbo cars, just meant it held decent torque to redline (as peak power was made at 7k).

Well that's cause we aren't talking about RB25's in here

Haha of course, I personally don't have much experience with them, just trying to get my head around the different turbo configs and how they perform. It is my next upgrade when I get bored of my 32 with 25det

Edited by Rolls

Realistically it's probably closer to 3500rpm than 4000rpm given it's not always loaded in 4th - but still both turbo choices offer a good spread of power.

This is on PULP as well. E85 will improve it a little from results seen thus far.

Piranha if you're in Sydney, it's easy enough to get you a ride in a 300kw GTR and back to back in a 400kw GTR.

I promise you will want the 400kw one then once you've seen them back to back.

Good point Ash made about one person's idea of lag against another. For example you may get someone thinking a 2.6L and GTRS's is a good setup-in most peoples minds they'd say that setup is totally crap, but the owner may like it.

See what you like and go from there :)

Yep I'm in sydney. That would be good to gauge the different turbos.

I have been in an s13 with rb26 and -5s but it only weighed 1000kg. Just destroyed the tyres. can't compare it with awd gtr anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide đź‘Ť
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
Ă—
Ă—
  • Create New...