Jump to content
SAU Community

R32 Parts

antz69
 Share

Recommended Posts

antz69 Community Regular

antz69

Posted
Posted

hey guys got a few things i wana get rid of

r32 GTR Rocker Covers(black) $120

R32 GTS-T Igniter pack $80

R32 GTST Power Steering pump $40

R32 GTST Cam Angle sensor $50

R32 GTST Rocker Covers $20

R32 GTST Fuel injectors & rail $60

R32 GTST Timing covers $20

R32 GTST Standard exhaust manifold $15

R32 GTST Inlet Manifold $30

R32 GTST Throttle Body $50

R32 GTST Standard Camshafts $40

All parts located in Melbourne s. e. suburbs

Link to comment
https://www.sau.com.au/forums/topic/237369-r32-parts/
Share on other sites
Craved Grand Master

Craved

Posted
Posted

yep i'll take

r32 GTR Rocker Covers(black) $120

R32 GTST Rocker Covers $20

R32 GTST Timing covers $20

if they arent deeply scratched or anything :nyaanyaa:

PM me if shipping isnt an issue

Link to comment
https://www.sau.com.au/forums/topic/237369-r32-parts/#findComment-4163750
Share on other sites
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • FRGTN1
      Fourth gear grind

      By FRGTN1 · Posted

      I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • RB2533
      UniClutch

      By RB2533 · Posted

      Yeah for sure that is peddle adjustment 
    • PotatoCake
      Attesa ETS Pro Install on R33 GTR

      By PotatoCake · Posted

      What are your thoughts on this after having it for a while, worth getting?
    • joshuaho96
      Fourth gear grind

      By joshuaho96 · Posted

      Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...