Jump to content
SAU Community

Recommended Posts

Item:R33 GTST S2 Front end, comes with Head lights in good condition, front bar with fog lights attatched and a Carbon fibre bonnet for S2 - the carbon fibre bonnet not in good condition but works normally

Age:unknown!

Condition:bar and lights good, bonnet average to bad condition but does the job!

Price:$1000 FIRM

To Fit:R33 GTST s1 or S2 (What car)

Location:Newcastle - PICKUP ONLY - can organise to be delivered close by for a price

Contact:Me 0412417579

Comments: Pics will not be available till the weekend. I WAS going to keep this for my car but i need some cash desperately, this front end was on a Series 1 but it is a S2 front end!

Item:RB25DET Engine

Age:13 years??

Condition:Good!

Price:$1100 !!!! CHEAP

To Fit:Anything :thumbsup: (What car)

Location:Newcastle NSW

Contact:ME 0412417579

Comments:This RB25DET has NO coilpacks (but can supply a set of S2 coilpacks and loom for a extra $100 and has NO turbo. It does have all the turbo lines and the inlet manifold is complete with throttle body and exaust manifold is there. I need this Gone ASAP as i need the money so its going for CHEAP - working engine, i have seen it running for a few hours before i pulled the car down and it did not blow any smoke ran properly etc etc.

Engine comes complete

Minus coil packs and coil pack loom

Minus Turbo

Harmonic balancer / power steering pump INCLUDED

Starter motor if you need one little extra (we can neg)

Inlet manifold side complete with throttle body and injectors & wire loom INCLUDED

Stock AFM & Pod filter INCLUDED

Take this off my hands and make some cash!

Item:R33 S1 steering wheel

Age:same as car

Condition:good

Price:$100

To Fit:r33 S1 (What car)

Location:Newcastle

Contact: ME

Comments:good condition wheel. $100 pickup only.

No time wasters please. this is going cheap as and won't last long so if your not sure don't bother me im busy!

Sorry forgot to mention, the altanator is included with the engine and the CAS is there as well as well as the engine harness.

Have a 3" turbo back exaust.

Includes dump pipe and front pipe (in one) and catco 3" cat and full exaust with big cannon on rear. looking at $400 for the LOT!!

If you are not able to get rid of it quickly would you consider separating and shipping the s2 front bar to Melbourne as that is all i need.

Please PM me if you happen to change your mind.

-Jack

not seperating anything. This needs to go as a whole. Ive seen front ends like this go for over $1500.

someone snap this shit up! make a decent offer

forgot to mention it ALSO comes with a S2 aftermarket grill, its a GTR one i think has a big area in the middle.

Would be keen to see pics of the front end!! has the bonnet just gone shitty an oxidized or is it actually damaged?

You sure you dont want to post? I could be up for a road trip though :cool:

i think the front end is sold. I am def not keen to post it. i just cannot possibly do it. sorry guys.

Surely someone wants a nice cheap RB25DET ? i know im going to regret selling this later!

Would be keen to see pics of the front end!! has the bonnet just gone shitty an oxidized or is it actually damaged?

You sure you dont want to post? I could be up for a road trip though :merli:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Unfortunately haven’t taken pics yet after it was finished. All the edges are hemmed nicely, just had to cut holes for the gear shifter and seat bolts and seat belt bolts in the rear. The molds seem like they’re done with steam and a layer of glue on the underside to hold a bit of shape but still soft enough that it’s a good fit when it’s all pressed down.
    • When's the rear mounted turbo kit coming? Needs dose and V8 chop idle lol.
    • I was very unimpressed with how the car came up from the A pillar forward, before I hit things (twice). It all has to go. It had to go, but now it has to go... more. So we finally found the very first Shennanigans with the entirely perfectly setup engine that had no problems being pulled apart to improve on 'was perfectly fine'. Cam bearings looked a bit... stock. Which isn't entirely bad given they were stock and this is a ~20 year old engine. So new cam bearings are on the way because it's somewhat difficult to get to this stage to do it later, and it will trash the block. It was quite unusual that it wasn't done when the perfectly new-looking VCM cam was originally installed by [unknown] What IS unusual is the cam that was installed there was advanced SIX degrees. As to why there is no way to know.. however it could have been @Dose Pipe Sutututu's mate who wanted a larger cam sound but also wanted it to come on earlier to be more usable. This is my dyno sheet with the previous setup - This cam is not supposed to peak until 7000+ RPM, according to VCM. This is what lead me down the whole 'my heads/intake setup is running out of puff and can't support the cam' line of thinking to begin with. Anyway too late now - New cam is in! It could be rather funny if this smaller cam acts like a larger cam because it isn't advanced six degrees. In the spirit of everything is working amazingly - the COMP cam required no dialling in whatsoever. It was about 0.5 degrees advanced, which seems pretty bang on. Any adjustment either way would be further out. I'm told as a chain breaks in it ends up regarding back about 0.5 a degree as the chain breaks in, making it bang on. In the spirit of everything was previously working amazingly - The timing gear that was taken out turned out to be was an N-Motion double timing chain kit, with adjustable cam gear (which is how it was 6 degrees advanced) and all looks entirely perfectly new. It also had a Torrington bearing, which was one of the reasons I ended up getting the Cloyes kit which they used in the C5R 24 hour racecar - Because I couldn't confirm what was in the engine when talking to Tony Mamo. I did believe however it was a Double chain kit of some kind... but found no supporting documentation or evidence for it.
    • I recently did this to my R33 with the full set from Car Mats Direct, they can't do the vinyl anymore that's advertised on the website due to a supplier issue so I ended up with the Black Loop Pile which looks great. I went all out with rubber sound deadening sheets from Repco and also added the sound deadening foam layer option with the carpet. Makes a world of difference and got rid of all the weird smells in the 29 year old interior. It was a bit of work but I'd 100% recommend it, Car Mats Direct had awesome customer service and quick postage. Replaced my seats with some sporty ones from Autotechnia while I was at it, feels like a new car.
×
×
  • Create New...