Jump to content
SAU Community

Recommended Posts

Hi guys,

i am getting a R33/34(prefer34) NA RB25DE Skyline. I am 24 so turbo rule doesn't apply to me. i want something cheaper to run (than a turbo) but with descent performance and handling compared to Falcon and Commodores.

First thing i will do is get good rubber if not there already.

1)Am i able to rev the engine to say 5000revs a few times a week without harming engine. (Will get services done every 5000km etc)

2)Looking for some upgrades when I get the car. How much would better suspension set me back.

3)Would i get any extra KW aftergetting extractors and Exaust installed. How much will i be looking to spend.

4)How hard is it to find parts for this car e.g. timing belts, brake pads etc

And my last question may sound very supid, dumb, childish and idiotic but please bare with me (you can have a laugh)

I love the idea of seeing those red brake caliper on cars that can be seen through the alloy wheels, you know like the Brembo ones. Is there anything you can get to make that effect happen. Seen most R33/34's have the Black Nissan caliper.

thanks guys.

Edited by ppshy1
Link to comment
https://www.sau.com.au/forums/topic/237656-getting-a-r33r34-na-rb25de/
Share on other sites

1)Am i able to rev the engine to say 5000revs a few times a week without harming engine. (Will get services done every 5000km etc)

Yes you can, they're decent twincam engines and don't mind revving, they sound best over 5000rpm anyway :P Seriously my car will often see the rev limit, it's governed anyway to a safe level.

2)Looking for some upgrades when I get the car. How much would better suspension set me back.

If you want to do the suspension get a complete handling pack from whiteline...current prices are on their site

3)Would i get any extra KW aftergetting extractors and Exaust installed. How much will i be looking to spend.

Yes you will for sure, cost is open ended really. You can get cheaper exhaust put together or see someone for a full custom job ($2000+)

4)How hard is it to find parts for this car e.g. timing belts, brake pads etc

Very easy, Nissan stock most parts, Nissan NZ are the most helpful though....realistically all places like Supercheap and Autobarn will have what you need, including caliper paint to get those red calipers :P

Thanks guys,

About the brake caliper paint i found a DIY on this site. Got to find a weekend to do it and get drunk while painting it.

1)I went to a dealer today and talked to 2 car owners from Car Sales and they are running either 95 Octane or 91. I thought only 98 could be run on this cars.

2)Some guy has short throw shift gear in his car. what does this do and am i able to remove it.

3)I saw 3 cars in total so far and one had Maxxis tyres and one Bob Jane Performance tyres. They any good or will i have to change straight away.

cheers

it is safe to run 98 all the time....

depends how much you love your car i guess

they are tuned in japan to run 100 octane...am i right guys?

my cousin use to fill 95 in his 34, and then run 98 once a month.

1)Am i able to rev the engine to say 5000revs a few times a week without harming engine. (Will get services done every 5000km etc)

Absolutely not a problem! My car sees that several times a week. Perhaps more.. depends if I decide to go for a spirited drive or not.

As long as there is regular maintanence performed and there isnt any pre-existing mechanical problems with the engine than its absolutely not a problem

2)Looking for some upgrades when I get the car. How much would better suspension set me back.

Well what are you looking at getting?

Best bang for buck in terms of suspention is sway bars. These will stiffen the chassis up, lessen body roll through corners and (if you buy the adjustable ones) let you change the mount of under/oversteer the car exhibits. These will set you back $400 odd.

Front strut bar is almost a must! R34's come stock with them. Rear strut bur is not essential as there isnt a massive gain to be had.

From there you can get:

New springs and Shocks (dunno price)/Coilovers (1200+ new - $1500 for a good set) - I suggest this only if you intend doing track days or heavy mountain road driving

New bushes - $100-$200 gives a more direct steering feel and steering responce

I have a feeling I missed something

Not really a suspention mod, but to get the best out of your suspention I highly recomend a good driving seat.

3)Would i get any extra KW aftergetting extractors and Exaust installed. How much will i be looking to spend.

Extractors - $350-$400 odd

Exhaust - $300 odd (second hand) $600 (new)

Extra KW? dont bother. not much. You will gain some responce and better exhaust note though

4)How hard is it to find parts for this car e.g. timing belts, brake pads etc

very easy.

Nothing like cold beers while working on the car :cool:

Enjoy it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...