Jump to content
SAU Community

Fs Vic - Sports Steering Wheel

private9
 Share

Recommended Posts

private9 Community Regular

private9

Posted
Posted

Hi All,

I'm no longer using this, so it's up for sale.

It's an Autotechnica leather steering wheel. No boss kit.

It's grey and black in colour, and the padded centre section can be unscrewed. Overall it's in VGC and there's no wear on the steering wheel, other than 1 very small tear near the bottom of the horn button. I will lightly glue this down before it's sold.

I'm after $90 for the wheel.

Pickup is welcome from either Cheltenham or Reservoir (BH), or I'm happy to post at the buyer's expense.

Please post or PM for any queries.

Thanks,

Justin.

Pic with horn button/pad

IMG_2251.jpg

Here's a pic of the wheel without the centre section. You could use it without the centre section, you'll just be left with the 3 small screw holes. Obviously the horn button goes back in the middle.

679.jpg

Link to comment
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Thank you for the links. I’m going to go with the 6pin plug you used. next step is rust treating re painting dash support bar and steering column then the 6pin cradle plug when it arrives in the mail.
    • soviet_merlin
      Nismo copper mix twin “pull” pedal height engagement

      By soviet_merlin · Posted

      I don't how much the car makes a difference or whether it is just a question of gearbox and clutch. On mine it's fine. Pull type Nismo coppermix twin (standard, not competition) on the 5 speed in my Stagea. OEM slave cylinder. Bite point is a few cm off the very bottom of the pedal. Clutch pedal all the way down to put in gear, and when heading off at the lights, there's a tiny bit of nothing and then it starts biting. And fully engaged before the pedal is all the way released. There's a bit of play at the top where the pedal does nothing anymore. Are you in Australia @ck_chino? If you are set on using a Nismo slave cylinder I have one new-in-box at home. Ordered it together with the clutch but didn't get it fitted. We can work something out if you want it
    • Butters
      Nismo copper mix twin “pull” pedal height engagement

      By Butters · Posted

      I am using a pull nismo coppermix twin in an r34 getrag box, had both the standard slave and  then the nismo one. Adjusted pedal to get bite point how I wanted , it is on the higher side, but would fully disengage past half way down.  I also read that the nismo slave won't work but I had no issues with the stroke, might become one later as clutch wears but 2+ years of happy motoring so far.  Take the above as one input only, specially as my setup is a bit unique in that I am using an S15 clutch master , cefiro clutch pedal, custom braided clutch line. Lots of variables at play. 
    • dbm7
      Got this r31 silhouette flood car to rebuild.

      By dbm7 · Posted

      Oh for sure, I'm just recounting my thoughts 😎 I'm not what you've got there to fuzt with.... likely my first idea was on the money -- rebuild or replace connectors. You can get a lot of connector stuff here  -> https://www.rapidcables.com.au/ Didn't look in the boot of mine, because I replaced these when I renewed the pump (plastic of connectors had gone brittle) edit: what I used... https://www.efihardware.com/products/2120/Deutsch-DTM-Connector-Kit-6-Pin ...cheaper... https://www.ebay.com.au/itm/364900039138
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      In no way was i suggesting it’s your fault mate. The trailer cable has a plug that I removed. I will have a closer look, but I did remove the trailer wiring cable with the tow ball as I don’t need it on my silo. i have replaced the fuel pump already there’s no need to remove the cradle again I can see the wire colours from it in.
×
×
  • Create New...