Jump to content
SAU Community

Recommended Posts

basically i am selling my car and a guy came and had a look and was worried about a bit of oil on the block (comes from leaking rocker cover gasket, same as what skylines suffer from) and he wants to do some tests on it to make sure the head gasket isn't gone. now i know you can do a pressure test, and a compression test (but neither will tell you if the head is leaking oil due to the head gasket). i explained that to him but he said that his mate has a few testers that don't require removing anything.

what could they be?

i was talking to my mate who is a mechanic and the only thing he could think of a TK test, but again that won't tell if the headgasket is the cause of the oil leak. an oil pressure test probably won't show it either if it is a tiny little leak (but as i said it's the rocker cover gasket leaking and i told the guy that). the only thing we could think of is that this guys mate has a crystal ball, or is a psychic.

so any ideas on what this guy is on about?

Link to comment
https://www.sau.com.au/forums/topic/238249-engine-tests-what-sorts-are-there/
Share on other sites

the only ones that wouldn't really require anything being removed would be compression and leak down afaik.

or he is trying to blow something minor out of proportion to try and hammer the price down.

Edited by TiTAN

both compression and leak down require getting to all cylinders, which means removing the manifold to get to the rear 3 cylinders in this case. which i told him i wasn't keen on doing because it takes a few hours to remove and install the manifold, and if the gasket gets damaged i have to get a new one of them also.

and none of them are going to able to really tell you if the head gasket is causing the oil on the side of the block (which is why this kid - he's only about 19, wants to do the tests). he just really doesn't seem to know what he is on about. and is getting advice from his mates who also don't seem to know too much.

as for trying to get the price lower, that isn't going to happen. and he has told me that many times he is keen, so why should i lower the price? if he didn't think the price was reasonable he wouldn't be saying that he is keen to get the car in every second message.

There are no other tests he can do other than the ones mentioned above. The oil won't be coming from the head gasket. Change the RC gaskets and clean the oil down. Drive it for a couple of days and see if the oil re-appears.

I think he maybe made a comment without thinking about it and is now trying to backpeddle via bullshit. Call his bluff, tell him you know he is full of shit, there is no test that can tell you where the oil is coming from.

Fix the highest leak...clean down...and re-check.

the rocker cover gaskets were replaced before i bought the car (to pass the roadworthy) but the new ones only stopped the leak for about 2 months.

oddly enough he didn't show up last night. on monday night i explained to him that neither a compression test nor a pressure test would show the leak and explained why, and i said i wasn't going to let him do a compression test due to the work involved removing the manifold. and that's when he said his mate had these other testers that didn't involve removing anything, to which i replied that i was interested to see what the testers were.

so i think he was going to try and do a pressure test, etc and tell me that the results were bad and when he found out i know what i'm doing he has had second thoughts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday, Due to not finding much up to date info on this topic I thought I'd make a thread to get peoples latest opinions/recommendations. Background info -  I've got a S1.5 R33 GTST as a fun project car, mainly for street use and occasional drag strip, apart from all the cosmetic things I'll be doing a full rebuild of the engine with forged internals. Since it'll be getting new cams (kelford) and springs to match I thought I might as well get new lifters and valves while I'm at it, the dash says 160k KMs but the engine seems pretty tired, compression measures about 130psi across all cylinders so I'd like to freshen everything up. This is where I'm tempted to just fork out the extra and go solid lifters while it's all apart, aiming for 400-450kw atw with a flex tune. Assuming all supporting mods (oiling, fuel and all bolt ons) with a lightly ported head and turbo to match (yet to make a decision possibly gtx3582r or similar from Hypergear) I've seen the Tomei kits with just the buckets getting around, Supertech sells most things - Supertech High Performance Cam Followers | Trusted Racing Cam Followers Questions -  Has anyone found the Hydraulic lifters to limit them at this power level? Is it usually found that you can just clean the stock lifters and find they work fine?  Does going solid lifters save any headaches/issues with hydraulic lifters in the future? Any recommendations on other things that will need to be replaced, I know I'll need to get the solid profile cams but can you use the same type of valves and springs/retainers and is it recommended to change the guides and stem seals?    Summary -  Basically looking for pros/cons and wanna know if I'll actually need the extra RPMs from solid lifters or it'll just be bragging rights to say it ReVs OvEr 8000 Cheers
    • Ha ha ha, this stuff they had was installing Toshiba PLCs that were made some time in the 1990s, and they were replacing GEM80 PLCs. To let those two talk (staged upgrade along a ~1.2km long building that was split into 4 sections), was a bunch of WinXP machines running Java gateways... There was no way to put something like ProfiSafe in... Most of the HMI machines were WinXP, with Java program, with a custom button board emulating a keyboard... About the only buttons in the operator stations that went direct to the PLCs was the eStop. There was some interesting design stuff in that place...
    • Stock bypass valves are good for plenty of boost.
    • Check for fuel flow out of the outlet end of the rail. Check for spark. Try to start with aerostart (or pressure can brake cleaner or similar solvent in a car) prayed in through TB. If you have fuel and you have spark and it will fire on substitute fuel, then seriously suspect that E85 sitting for ages in your fuel system has destroyed something and put it in your injectors.
    • Nissan stock oil pressure is typically about 1 bar at 1000 rpm plus about 1 bar per thousand revs on top.
×
×
  • Create New...