Jump to content
SAU Community

Recommended Posts

Hey Guys,

So ive finally gotten around after been sidetracked with other modifications to my car, to finally start to increase the power.

Ive just gotten my hands on a SAFC 2 and was now wondering what type of boost controller to use?

Ive been thinking either pro spec 2, AVC R, E-O1 or EVC 5... ? What do you guys think?

Also in regards to tuning, i know their is a conslidated workshop, but any personal experience when it comes to getting a r33 tuned? Im SOR, i dont mind travelling NOR to get it tuned.. How long does this normally take?

And one more thing, atm i am only running a HKS Hi power Silent cat back system.. is it reccomended that i change this to a full turbo back before i tune it? If so, what parts do i need? Hi flow cat, dump pipe? Front pipe? What brands are good for this (Was going to go xforce, but heard it was no good)? I want to keep it quiet as i like to b a low profile.

I am also going to change my clutch in the near future (Holidays coming up, so bulk working to get cash!! ) Should this also be done before tune?? Or does it not affect it?

Cheers for your help guys.

Edited by br3ndan
Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

I would modify as much as i can before i take my car for a tune.

haha, if i did that, it would never get tuned! haha..

THats why i need to work out when i should tune it, im pretty sure i should at least get the full exhaust done? Since safc is "super air flow controller" ?

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174652
Share on other sites

ive had experience with the safc 2 and the avcr 2 and i would say they work pretty well together. If you have piggy backs, it shouldnt cost too much to retune after the first tune. I would definitely do the cheap stuff first like zorst and filter and small things like that before i have my first tune.

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174712
Share on other sites

Atleast get a full exhaust done to make it free flowing. maybe you could put a fuel pump and get an AVCR

When i got my car tuned by ovaboost with 3inch turbo back, SAFC, pod filter, 10psi i got around 220hp.

Then with front mount, fuel pump, and EBC at 12psi i got 270hp

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174725
Share on other sites

Yeh i agree with lunjiaow, most of the tuning places told me to get spark plugs/ fuel pump before a tune otherwise its a waste of time tuning it.. i already has alot of the basic mods..

As for exhaust i already had bought a full exhaust before my car landed on the boat :(

When you go from full 2.5inch to full 3 inch in one hit.. man what a difference :D until this day its been the biggest increase in power ive had, but thats partly because on stock boost you get a few more psi out of the car

I was always told not to go those apexi avcr's by a few places.. they use the same boost control bit as the boost control kit on the apexi power fc's and theres a reason no one uses them, thats going on xspeed info anyway.. they also told me my car couldnt have a gtr diff, but yeh id recommend a blitz or or a greddy boost controller. the hks ones are good aswell but expensive, some of those turbosmart ones are good aswell

i got my car tuned by top racing n with a power fc i made 285rwhp on 12psi :D go the power fc lol

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174736
Share on other sites

thanks for the advice so far guys

I already got hks pod and FMIC (installed couple of months ago in pepretation for boost increase) and 3 inch cat back, spark plugs were also change about 3 weeks ago to irridium ones, so looks like ill finsh up the exhaust so its 3 inch all the way first before the tune can anyone let me know exactly what i need/brand is best?.. As for the boost controller i am more leaning towards E01 .. anyone got any experience with it?

As for fuel pump, which one is best ? i am probably looking at 200kwish after the full exhaust and tune right? So any advice on fuel pump?

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174749
Share on other sites

id recommend one of those front/dump pipes in one with the open bellmouth, just with the amount of problems ive seen people have with the split ones not being able to control boost

the cat you can either go a cheap cheap crappy one like those 3inch x forces.. with a crappy core.. they are alrite for the 175 you pay for them.. i been using one for a while started off alright but i think its a little blocked up now.. or you could spend a little extra a get a metal core one for 400ish, lots of companies sell them.. catco, x force, metalcat, magic.. take your pick :merli:

they all flow pretty well and all claim to outflow the others, in the end i bought a 3.5inch xforce coz it was the only one i could find in stock for that size with flanges

fuel pump those walbro ones are the bottom of the barrel but do the job alrite, i think they are 170ish from slide, but i would probably lean towards a bosch one either the 040 or 044, if your confident with some simple wiring they are pretty easy to install.. they are around the 230mark or if you want a direct replacement ( comes with new cradle, wiring and filter ) go for the tomei/nismo ( same pump) i think slide sells them for 430 but theres some places like nengun that sell them in the high 300s.. maybe try greenline

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174799
Share on other sites

Hey Guys,

So ive finally gotten around after been sidetracked with other modifications to my car, to finally start to increase the power.

Ive just gotten my hands on a SAFC 2 and was now wondering what type of boost controller to use?

Ive been thinking either pro spec 2, AVC R, E-O1 or EVC 5... ? What do you guys think?

Also in regards to tuning, i know their is a conslidated workshop, but any personal experience when it comes to getting a r33 tuned? Im SOR, i dont mind travelling NOR to get it tuned.. How long does this normally take?

And one more thing, atm i am only running a HKS Hi power Silent cat back system.. is it reccomended that i change this to a full turbo back before i tune it? If so, what parts do i need? Hi flow cat, dump pipe? Front pipe? What brands are good for this (Was going to go xforce, but heard it was no good)? I want to keep it quiet as i like to b a low profile.

I am also going to change my clutch in the near future (Holidays coming up, so bulk working to get cash!! ) Should this also be done before tune?? Or does it not affect it?

Cheers for your help guys.

What do you want to do with the car (daily/track/drag etc) and what sort of driver experience are you looking for?

What aspects (accelleration/braking/handling) are you looking to improve and whats most important?

Answering these can help get the money spent where it's going to give you the biggest buzz.

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174839
Share on other sites

What do you want to do with the car (daily/track/drag etc) and what sort of driver experience are you looking for?

What aspects (accelleration/braking/handling) are you looking to improve and whats most important?

Answering these can help get the money spent where it's going to give you the biggest buzz.

My handling is good at the moment. I got sturt braces and HKS coilovers installed, that coupled with nice quality wide tyres has got my skyline to an acceptable handling mark for the moment.

Braking wise is still pretty stock, running some good quality bendix pads tho. So far thats the only upgrade their.

Power wise, im looking for a bit more "umph" on take off. when i first got the skyline it pushed me back into the chair, now after about 8 months driving, ive seem to have gotten use to it. And after spending big bucks on handling and just general maintaince (ive changed all fluids and i mean all! since i got the car and have changed radiator etc etc and im reguarly generally maintaining it (new sparkies o2 sensors etc)), its time to put a bit of money aside for power.

Hope this helps in giving me some more advice...

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4174974
Share on other sites

First cab off the rank is to get the clutch and flywheel lined up. The stock clutch friction plate will die.

If you want a good clutch setup for anything up to 400rwhp, Ross from Autoclutch in Osborne park can sort you out for one of his versions of a 9 puck ceramic 'sprung' clutch plate and I would consider going to a chrome molly flywheel ( more response and accelleration) while you are at it. Stick to the factory pressure plate pressure. You do not need more until really you are ready to bite the bullet for a twin plate. It's a mistake to get more pressure than you need and takes away from the driving experience.

The exhaust (front & dump pipe) can be done by a local exhaust place. My pick is Mettams Morley (ask for Pat) 21 Rudloc Rd, Morley, WA 6062 - (08) 9275 7034‎. The guy does amazing work and the prices are very low considering how good the quality is. Along with lots of other performance nuts I have utilised Pat's skill for many years on lots of cars.

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4175812
Share on other sites

I am also going to change my clutch in the near future (Holidays coming up, so bulk working to get cash!! ) Should this also be done before tune?? Or does it not affect it?

Definately go the clutch man. As soon as you put some real boost into your baby you'll fry it within a month. Go the ceramic/copper as the organic will wear quicker, and the ceramic/copper has more bite. 9 puck if you can.

As for exhaust, go the 3 inch all the way through. Whether you use a split dump and downpipe or dump/downpipie with divorced wastegate is up to you, but it's a must. Personally the divorced downpipe is better as it introduces the gases further down the system and produces less cavitation. Also a hi-flow cat is a must as the stockie is a restrictor.

I'm using a Walbro which is good for 450hp. Nothing wrong with that! Make sure it's genuine and not a cheap-ass asian knockoff and you'll be fine. Bosch's are the sweetest but for the power you'll be chasing the Walbro will do the trick.

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4176298
Share on other sites

the clutch go a 5puk exedy good for 300rwkw... little difficult to drive at first but is light and loves getting dropped hard :thumbsup: mid 400s from slide and easy to install yourself, if you run into any troubles give us a message.. just make sure you have the clutch centred... i used some dowel(i think its 16mm) with some tape.. and jack the engine up abit makes it alot easier to get the gearbox back in... not that hard saves yourself a easy 500 dollars for an install :D you really do need 4 jack stands tho..

i disagree tho full 3 inch exhaust first.. up the boost abit and see how it goes.. a mate of mine's stock clutch lasted him a year like that.. mine lasted me 2 months but i do alot of burnouts n drop it alot.. but once it starts slippin abit you can just baby it until you have the money for the 5 puk =D

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4176527
Share on other sites

Thanks for you concern 2ltrv8

But i only plan to boost it to 0.7 bar... not much at all i know. But i think that way the clutch wont die so fast on me until i can replace it with some more heavier. Then after that i will turn up the boost a bit more.

Im just very confused with the dump/front pipe.. there are so many styles to choose from i really dont know what to pick.

I guess more research for me..~

Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4176543
Share on other sites

The bell mouth is less problematic. To do a 'good' split involves a relatively long sepparation in order to caputre the turbulence benifit.

5 puck non-sprung clutches are rubbish to drive by comparison to the 9 puck sprung units availible.

Why budget for the clutch first?

*if you are making good power the factory clutch will die fast.

*banking on old parts not designed for the power increase, lasting is the dumber way of doing things with performance cars. The 'my mate had one that went for 10yrs' advice is sometimes dispensed by people with the disease of false hope. Get rid of that when you understand you have an addiction to cars, it saves you pain.

*when it dies you have the massive hassle of it potentially letting go somewhere you would rather not be stranded.

* If you have upgraded the clutch the odds of this hassle are pretty much nill.

Edited by rev210
Link to comment
https://www.sau.com.au/forums/topic/238846-advice-needed/#findComment-4176549
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, if I need to fit people in a car I'll just use the Mrs car, the MX5 is perfect for what I need as a fun little sports car for fun on the street As for getting in and out of the MX5, I have no issues as I am a short arse who does lots of mobility training 🥷 If anything, I have been looking at Daihatsu Hi-Jets for a work hack, I helped one of my mates move some stuff with one recently that he picked up from Just Jap, it was a little ripper and plenty big enough for what we needed, it would also be super handy for me as I do alot of gardening, and plan on having some veggie patches and native gardens in the place I buy next year when I retire I did alot landscape gardening and growing veggies prior to my current job, and loved it, and that is a hobby that can keep me sane in my retirement, and as such, the little 300kg load capacity would be more than enough for what I need it to move around I have been looking at utes for just this purpose for a while now, and a near new 2024 Hi-Jet can be had for under $30k And I would rather look at a quirky little Hi-Jet than pretty much any other little ute, well, apart from a Brumby, I love the little Brumby, and weirdly have never owned one yet I was going to buy a heap of raffle tickets to try and win the Brumby that MCM built for Subaru Australia, but sadly I totally missed the raffle, I even filled in some form to be told when the raffle started so I could buy tickets, but to my dismay I was never contacted and found out I missed it when I was randomly googling Brumbys last year... #conspiracy  Maybe I should just buy a Brumby for a little "work hack".....LOL I use to be indecisive, but now I'm not sure
    • Well.... it's not just "de-oxygenating". If you do that you just have, most likely, ethane. So you still need to do a synthesis step to combine a number of ethanes/ethanols to make circa-8-chain hydrocarbons. And of course you don't want straight chain HCs, because n-octane actually has a negative octane rating (ie, it's worse even than the n-heptane which sets the zero on the octane scale!), so you have to do some tricky catalytic chemistry to synthesise branched HCs. That's all doable - but it doesn't come for free. And.... it starts with ethanol, which is an agricultural product, and there will almost certainly never be enough of that as a base stock to replace the liquid fuels that are in use. You really wouldn't want to be planning to be using any more ethanol for fuels than is currently already used (in E10, E85s, etc). And ideally you'd be looking to reduce such usage, as it is largely wasteful, particularly in the stupid-ole'US-of-A where the corn lobby has organised it so that it's actually primary production corn that is used to make a lot of the ethanol, not by-products and waste, like it is (mostly) elsewhere. So, what I said about needing free-ish energy probably still applies. True synth fuels would be made from H2 and CO2, in a near reversal of the combustion process. In fact, given that the H2 would be split from water first, it actually is a complete reversal of the combustion process. But...energy intensive. The human race burns something like 1 cubic MILE of crude oil, after it has been made into various fuels. Every year. That's a simply stupendous amount of energy. Just assume that the density is 900 kg/m3, and that the calorific value is 45 MJ/kg, then that is 165.9 x10^12 MJ of energy. Or more than 10^19 Joules. You get a maximum of 1 kJ/s per square meter solar radiation falling on the planet's surface, and so if you halve that for daylight, and halve it again for average weather (highly optimistic) and then take ~25% for the very best efficiency of solar panels, then you need about 85.7 billion square metres of solar panels to generate enough electricity to replace that liquid fuel energy consumption. Each panel is about 1m2. That's a rather large number of panels. We also burn about a cubic mile of coal. We also use hydroelectric power. We also use nuclear. We also use a number of other sources, both "renewable" and not. You can kind of ignore the renewable ones (except for hydro, because it will all end up getting subsumed into pumped hydro for storing other renewables, and so it won't be the standalone renewable that it originally was), so we end up needing a multiple of the ground area number that I just arrived at.
    • Corvette thread then? Don't say I didn't predict the future again. "I love the little MX5, I do, but I just want something a little easier to get in/out of, a little more cushy and some power would be nice - I miss the V8 Rumble... I found this clean red C5 for sale recently and..." I'll do you a great deal on the next step, which is one of those but you can fit people in it, too.
    • What about renewable diesel and/or gasoline? I see some projects spinning up like de-oxygenating ethanol to make drop-in compatible bio-gasoline especially in CA. I still think the future is EVs and we should've all gone full throttle on nuclear power after the 1973 oil crisis like France. Despite 15 years of work in CA to reduce the CO2 intensity of generation with renewables our electric grid is still far worse than even "low carbon" nuclear power. ICE is pretty cool when you aren't depending on the stupid thing to be practical and reliable and cheap as possible to get you to work every day. It's kind of like mechanical watches or vacuum tube amps.
    • I just rolled over "my" first 10k km in the MX5 Every time I go anywhere it always ends up in a adventure to look at houses and find some random country roads I've been on leave since early November but unfortunately need to go back to work on 19 January Luckily though I still have a fair chunk of leave left to burn until.... Not that I'm counting 😁
×
×
  • Create New...