Jump to content
SAU Community

Recommended Posts

we used a rb25 turbo on an rb20 and it was making 271rwhp on 17psi

so there is nothing wrong with using a 25 turbo iether just personal preferance and budget..

Rb20

VG30

FMIC

Fuel Pump

Exhaust

198rwkw @ 15psi

Did 1 run on 17psi and was going past 208rwkw when it ran out of fuel and was backed off, probably didnt have much more than 210rwkw.

Rb20

VG30

FMIC

Fuel Pump

Exhaust

198rwkw @ 15psi

Did 1 run on 17psi and was going past 208rwkw when it ran out of fuel and was backed off, probably didnt have much more than 210rwkw.

hey bro, thanks for the power figures :O.. will upload mine once i do my tune soon

  • 2 weeks later...

niran, where are you looking to get your tune done in the perth area?

i am also looking into the VG30 turbo setup..

(sorry about posting 3 times, comp messed up :P)

Edited by fourdoorlove
niran, where are you looking to get your tune done in the perth area?

i am also looking into the VG30 turbo setup..

(sorry about posting 3 times, comp messed up :) )

Hey bro

Yep i am going to be getting it tuned in perth.. i just got a yellow sticker so just been busy trying to get that off.. but after that the plan is to buy some r32 gtr injectors, and then give it to all star garage and get them to install a nistune chip and then get them to tune it.

Thanks niran

guys i need some info asap how do you tell the difference in the

Ballbearing vg30 t3 turbo

and the

Jurnal bearing vg30 t3 turbo

need info a.s.a.p?????????????????????????????????????????????

Hey man

I think it goes by the versions.. There was another thread where i asked the same question as you did and its somewhere on skyaus most likely on forced induction.. Besides that if you already have the turbo you could go to a jap shop and ask them too

niran

  • 4 weeks later...
  • 1 year later...

i recently got a vg30 turbo to bolt onto my rb20, i have a few questions though, how do i find out if its ceramic or steele? it sais 45v2 on it.

Also, im putting the rb20 actuator on the vg30 turbs, will it hold 15psi or will i need an external wastegate?

  • 4 weeks later...

how are u guys runing 17 psi through the vg 30 turbo if it has a ceramic exhaust wheel. is there a ball bering version with a steel exhaust wheel? and what are u doing ecu wise to run 17 psi remap? or just a tune?

niran i got

FMIC

exhaust

040 FP

Ebc

i want 198rwkw

what do i have to do apart from bolt the turbo on? coz that bit is no prob

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Turbo gods, some assistance and recommendations please I'm looking into a turbo kit for my 2.5 from MX5 Mania >>>>> https://mx5mania.com.au/products/copy-of-mx-5-nc-2-5-litre-engine-conversion-turbo-2005-2013 Power wise I would like about 200kw atw, and of course dose noises, apparently if you keep a stock 2.5 under around 200kwatw the engine and drivetrain will not hate life even when ragging on it a bit Max RPM on the 2.5 is around 6500rpm The turbo MX5 use is something around the disco potato size as  packaging room for the turbo is pretty limited, which will, I believe, give me my power goals I want and not have the turbo either under, or oversized, but the rear housing bit is confusing  It comes with either a 0.64 or 0.86 From my understanding, which so far is based off googling, so make of that what you will 0.64: spools faster = good Makes more EGT heat on boost = bad Less topend power than 0.86 = I'm only looking for 200 atw so that point may be mute????, I don't know, hence my questions  0.86: Spools a "little" slower = how much slower??? remembering 6500 is my max rpm Makes less EGT heat = good Makes a little more power up top = again, power goals is only around 200 Also, this is a street car, so there will not really be any long track sessions, in saying this I would want it so it was happy with at least 3 hot laps at Wakefield Park if the need arises  I already have a fancy pants triple pass radiator, and a oil cooler with thermostat will be getting installed as well Thanks for any information or recommendations you have 👍, and of course, the comments about me wasting money on drive in drive out modifications, or any other snide remarks about my manhood for owning a MX5 🤣    
    • Tape some wool onto the vent then take it for a drive I did this to my reverse cowl and was instantly unhappy, as anything over about 60kph would have the wool enter the engine bay, thus just adding underbonnet pressure and stooging my coolant stack, it did let alot of heat out when stationary though, which really didn't help once the car was moving, with the reverse cowl you could watch the coolant temps cheap up the faster you went on the hwy, I assume it would be alot worse doing track day speed With the vented bonnet (just after the radiator and about 1/3 up the bonnet) on my old R33 the wool on the leading edge sat at about a 45° angle as air poured out of it From looking where your vents are, and their size, I believe you should be fine at speed and air should be evacuated from the engine bay, I think it will be a night and day difference when stuck in traffic though for removing the trapped heat, and not sitting there cooking when parked up after driving around... #convection  Post wool tuft pics and data for science  This beastie is one nice and unique rig, enjoy
    • It is possible to do this stuff for "cheap". But you need to be able to get deals on all the bigger items, and it really helps if you're fully capable of doing your own work. As soon as you're paying retail for new parts, or buying "kits" because you can't fabricate necessary bits and pieces, and if you really need someone else to take the reins of doing the work because you don't have the space/time/skills/confidence to  rip deep into the car and put it back together in a working fashions.....then you pay. And these days, pay means a lot of money. You'd think things would get cheaper, but they don't. They just seem to keep getting more and more expensive.
    • It’s almost the price of an engine build, you won’t have anything to bolt onto it though 
    • Hopefully it's enough to help with the temps! I was also only shit stirring, regarding Murphy's Law basically. I've found, what ever spare parts I have, are the parts I don't break. Ever. Also have never had issues with oil/spinning bearings until I put oil pressure gauges on the car. 😛
×
×
  • Create New...