Jump to content
SAU Community

Recommended Posts

Thanks guys ;)

Sure I can give you basics :P

It's an SR20VE+T now, big custom cams, sleeved / forged bottom end, modded Precision turbo on 6boost manifold, ported head, oversized valves etc, Bosch 2000cc injectors, custom plenum, Plazmaman throttle body.

sounds wicked. there is some cool stuff happening around the place with the SR VET heads going on to SR20s. but your thing is out of this world. I'd like to come check it out one day soon. :)

It's an SR20VE+T now, big custom cams, sleeved / forged bottom end, modded Precision turbo on 6boost manifold, ported head, oversized valves etc, Bosch 2000cc injectors, custom plenum, Plazmaman throttle body.

Thats awesome, its a PT6765 I'm guessing? The Precision and the FP-HTA billet turbos are wicked pieces of kit, good to see them catching on down this part of the world. I am hoping that soon I'll be able to report some results for a built RB25 running a PT6765 on E85... that should be quite interesting.

  • 2 weeks later...

cheers mate, allways keen to try new things!

Yes i used to get 380 to 450km's to a tank with BP98 depending how i drove it. I came up with a magical number in my head when making up the map in datalogit on my pc at home which was spot on, and its no way near double then what it was, but i will say it is more then 25% consumption.

My gtr uses bout 20 litres per 100 ks I did a trip from.Brisbane to.tweed on.the weekend and.went through a tank in 180 km mind u its a very very heavaly modified engine

cheers mate, allways keen to try new things!

Yes i used to get 380 to 450km's to a tank with BP98 depending how i drove it. I came up with a magical number in my head when making up the map in datalogit on my pc at home which was spot on, and its no way near double then what it was, but i will say it is more then 25% consumption.

My gtr uses bout 20 litres per 100 ks I did a trip from.Brisbane to.tweed on.the weekend and.went through a tank in 180 km mind u its a very very heavaly modified engine

  • 2 weeks later...

Finally joined the E85 club! RB25 Neo with super responsive turbo making 242rwkw on 98 and 279rwkw on E85! Very happy

Havent tried cold start yet but my idle is smoother than on 98! Thanks Trent from Status Tuning and Tao from Hypergear turbos!

post-29432-0-66365500-1313121774_thumb.jpg

post-29432-0-97175300-1313121793_thumb.jpg

Hi guys,

I just had my car run on a dyno on the weekend, it pulled 353rwkw @ 24.5psi

the AFR's were dead flat on 11:1

boost held strong to redline, only droping maybe 1.5-2psi from peak.

question is, is 11:1 AFR too rich for E85? i dont think there is much advance timing in the tune, maybe 3-5 degrees over PULP

turbo's -5's

exhaust 3in full system incl 3in decat

nismo AFM's

std airbox

K&N air filter

1000cc injectors

Nistune ECU

twin walbro in tank fuel pumps

ARC 70mm intercooler

silicone I/C piping

std cams (recond when engine rebuilt)

forged bottom end

Mines dump pipes

std manifolds

that's pretty much it

That is very low power for -5s on 98 fuel. I would fix whatever the issue is holding that back. Should be able to make around 350rwkw on 98 first. 318 is -7 or -9 power. Whatever restriction you have may be holding back your E85 results in a more significant way.

honestly in my experience it's in the ball park. having seen dozens of cars with -5s most often they make between 310 and 340kw at 20-22psi. 353kw on E85 is not bad. perhaps a little low but every car and every dyno is so different as long as it's performing it's not worth worrying about.

Hi guys,

I just had my car run on a dyno on the weekend, it pulled 353rwkw @ 24.5psi

the AFR's were dead flat on 11:1

boost held strong to redline, only droping maybe 1.5-2psi from peak.

question is, is 11:1 AFR too rich for E85? i dont think there is much advance timing in the tune, maybe 3-5 degrees over PULP

11:8 to 12 AFR is the sweet/safe spot. Leaning it out a bit will net you some gains.

Hi guys,

I just had my car run on a dyno on the weekend, it pulled 353rwkw @ 24.5psi

the AFR's were dead flat on 11:1

boost held strong to redline, only droping maybe 1.5-2psi from peak.

question is, is 11:1 AFR too rich for E85? i dont think there is much advance timing in the tune, maybe 3-5 degrees over PULP

11:8 to 12 AFR is the sweet/safe spot. Leaning it out a bit will net you some gains.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...