Jump to content
SAU Community

Recommended Posts

Model:R 33 M SPEC

Milage:76000

Transmission:5 SPEED

Colour:SILVER

Location:BRISSY

Currently registered?YES

Price:$21500

Contact:0419 704 265

Modifications:SOME

Images:YES

ENGINE COMPLETE REBUILD 2500 KMS AGO

ENGINE CURRENTLY MAKING 440 RWHP ON 16 PSI

MODS AS PER:

MICROTECH LT12S WITH HAND CONTROLLER

GARRETT GT 35/40R TURB ON TOP MOUNT MANIFOLD

50 MM EXT GATE WITH SCREAMER PIPE

FULL 3 INCH EXHUST WITH OPEN CAT

CP PISTONS {FORGED}

COMETIC HEAD GASGET

RACE BEARINGS

BILLET HI FLOW FUEL RAIL

DENSO 680 CC INJECTORS

SURGE TANK & BOSCH 044

TURBO SMART HI FLOW FUEL PRES REG WITH GAUGE

TURBO SMART MEGA SONIC BOV

NICKS CLUTHES HP BUTTON CLUTCH

3 INCH COOLER

FULL 3 INCH S/STEEL COOLER PIPES

APEXI BOOST GUAGE

GREDDY EGT GAUGE

SASS STEERING WHEEL

SUN ROOF

TINT

HICAS LOCK OUT BAR

NEW 18 INCHMAGS

NEW 225 FRT TYERS

NEW 265 REAR TYERS

NEW BATTERY

NEW RADIATOR

FULLY RESPRAYED IN 2PAC

R400 FRT BAR

R400 SIDES

GTR REAR PODS

ANY QUESTIONS PLS CALL

MOTOR AND ALL ACC HAVE 2500 KM ON THEM

post-33883-1223377145_thumb.jpgpost-33883-1223377220_thumb.jpg

post-33883-1223377317_thumb.jpgpost-33883-1223377399_thumb.jpg

post-33883-1223377526_thumb.jpgpost-33883-1223377610_thumb.jpg

post-33883-1223377700_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/239290-hi-horse-power-r-33-m-spec/
Share on other sites

  • 3 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
×
×
  • Create New...