Jump to content
SAU Community

R33 Gtst


Turbo 33
 Share

Recommended Posts

and yes i did search

What is the part number for copper spark plugs for rb25det ?

Which ones should i get i have full 3in exhaust but with stock cat , fmic, pod filter ,10psi

i have changed them before but dont want to spend $26 a plug again

and seem to run pretty crap at the moment

What is the part number for fuel filter for rb25det ?

and what oil was using motul turbolight but want to try a different oil

what do you recommend

Edited by Turbo 33
Link to comment
Share on other sites

and yes i did search

What is the part number for copper spark plugs for rb25det ?

Which ones should i get i have full 3in exhaust but with stock cat , fmic, pod filter ,10psi

i have changed them before but dont want to spend $26 a plug again

and seem to run pretty crap at the moment

What is the part number for fuel filter for rb25det ?

and what oil was using motul turbolight but want to try a different oil

what do you recommend

BCPR6ES-11.

Z387

I recommend Royal Purple $66 / 5L

Oil Filter Z145A

Link to comment
Share on other sites

710 : Mobil 1 - but more expensive

plugs - BCPr6ES - http://www.skylinesaustralia.com/forums/Sp...&hl=bcpr6es

fuel filter - cant recall the number of the top of my head, but just ask you local repco or something - if unsure - its teh same as the Z32 300zx, just without the 90 degree bend on the outlet.

Link to comment
Share on other sites

Any semi synthetic or full synthetic oil is going to do the job. Full synthetic oils are a little bit better at handling tougher conditions so if it's a daily driver, you can leave oil changes to 10k intervals as the oil is more resistant to breaking down. Semi synthetic oils you'll need to change every 5-7k.

Pick an oil that is readily available in your area, a good price and has a good name. Mobil 1, Castrol Edge, Motul 4100 or 8100, Penzoil etc etc. These are all capable of doing the job well.

If you are tracking the car, then you need to be a tiny bit more picky on the oil you choose.

What are you going to be using the car for?

Link to comment
Share on other sites

Any semi synthetic or full synthetic oil is going to do the job. Full synthetic oils are a little bit better at handling tougher conditions so if it's a daily driver, you can leave oil changes to 10k intervals as the oil is more resistant to breaking down. Semi synthetic oils you'll need to change every 5-7k.

Pick an oil that is readily available in your area, a good price and has a good name. Mobil 1, Castrol Edge, Motul 4100 or 8100, Penzoil etc etc. These are all capable of doing the job well.

If you are tracking the car, then you need to be a tiny bit more picky on the oil you choose.

What are you going to be using the car for?

its a daily but will be taking in to drag strip maybe once a month

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • 8v - 2.48ms 9v - 2.15ms 10v - 1.74ms 11v - 1.41ms 12v - 1.15ms 13v - 0.99ms 14v - 0.89ms 15v - 0.82ms 16v - 0.81ms I'm running these values on my RB20 Neo with 570cc Denso R35 stock jets and it's great. Also bought a set for my Legnum VR4, love these injectors!
    • Thanks for your reply,  Those blue/green wires running to the actuator aren't attached to anything, so I'm not sure how the central locking is still working. I will have to take a good look tomorrow, I don't have the car with me. After googling it seems like a pretty common aftermarket actuator which even uses the same green/blue wires the immobiliser required. i'll test everything tomorrow and if it's working i'll melt the solder, strip it, resolder and neaten it all up with some heat shrink. I don't have to understand it if it works hahaha I just don't want a fire/ short circuit. That R32 diagram looks more like a continuity chart? Can you make sense of this form the R34 manual? 10V is probably due to very flat battery, i'll recheck as well tomorrow, I did have to jump start it haha. Thanks again!  
    • So, COM doesn't mean comms. It means common. What common itself means will depend on the type of device. For a two directional actuator (ie, one that can push and pull on the same output rod) then the common will typically just be the earth connection. There will be at least 2 other wires. If you put 12V on one of the other wires, then the actuator will push. On the other 12V wire, it will pull. Can't quite make out what is going on with the wiring of your actuator. It appears to have several wires at the actuator plug, but there only appears to be 2 wires where its loom approaches the door control module, with at least one of the others cut off. I don't know these actuators off by heart. I'd have to look at a wiring diagram for one before knowing what the wires were about, and that's despite me having to replace one in my car not all that long ago. Just not interesting enough to have dedicated memory set aside for trivia like that any more. That actuator is an aftermarket one, not the original one, which probably died and was replaced. That might require some sort of bodge job on wiring to make it work. Although nothing should justify the bodginess of the bodge job done. As to the soldering job on the door module's loom plug. Ahhahhahaha. Yes, very nasty. Again, I cant tell you what any of those wires do. You'd need to study the R34 wiring diagram (if you can find one that shows the door module). I don't think I have any. I'd have to study the R32 diagram to start to understand what mine is doing, and again, even though I've had a problem with mine for the last 25 years (where it locks the passenger door when the driver's window reaches top or bottom of travel) I'm just not interested enough to try to to work it out. So long as it's not burning down, it's fine with me. Here's the R32 GTR diagram, which, confusingly, has rear door lock actuators and window motors on it!! As you can see, unless you understand the functions of the door lock timer and the power window amplifier, you'll never be able to work out how it works just from the diagram. I don't imagine that the R34 one is any better. Hopefully an R34 aware bod can help. FWIW, the two wires that are cut and joined look like they are both power supply - so hopefully it is not fatal to join them. The 10V you measured on the cut off free end of one of them is concerning. You'd expect 12V, and it might be the reason for the bodge job joining them together.
    • Yeah, so try to post images with extensions that the internet can handle, not HEIC files which only arstyphones can handle.
×
×
  • Create New...