Jump to content
SAU Community

R33 Auto Wont Stay In Overdrive?

ZILLAR5
 Share

Recommended Posts

ZILLAR5 Explorer

ZILLAR5

Posted
Posted

ok this is really driving me nuts

i'll be driving along at 100km and all of a sudden it will go in and out of overdrive, in - 2650rpm .. out- 2900rpm usually when its warm. Other times i'll be driving normally and it will change down from 4th - 3rd without touching the accelerator?

i've searched the forum some say it could be the alarm causing it, i did get an alarm installed around the time it started?

another says to clean the plugs/sockets near the wiper bottle under the bonnet, trying this now.

Could the TPS be out of whack? i've had it off to clean, have i put it back in the right position?

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/239747-r33-auto-wont-stay-in-overdrive/
Share on other sites
Detour Explorer

Detour

Posted
Posted
anyone? btw i've taken to transmission shops and they all say it fine?

that happens to me exactly. It wont stay in overdrive especially when driving on 100km (car is warm) it goes from approx 2500 up to about 4000 revs then whenever it feels like the overdrive kicks in again. I spoke to my mechanic and he said to me that my gearbox is slipping. He also said that when it revs higher push the overdrive button on and off and see if it will help when driving at 100km or when it revs higher that its suppose too.

hope this helps

White GTS-T Mentor

White GTS-T

Posted
Posted (edited)

Have had two cars recently in the workshop, both presenting with the same aforementioned problem. Both, I'm sorry to inform you, had to have new/recod transmissions fitted. Not going into/staying in overdrive. When the converter starts to slip it heats the trans fluid massively and the trans fails.If you smell the trans fluid on the dipstick it will smell burnt regardless of colour. Unfortunately servicing the auto wont accomplish anything. I drove along with the scan tool displaying current data and manually put it in and out of overdrive and nothing happened.

The first thing i would be doing is getting the car onto a scan tool and go from there. Let us know how you go, good luck.

Edited by White GTS-T
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Milkmun
      The FD RX7 is the best looking 90's JDM car

      By Milkmun · Posted

      Lucky man, who owns it in the family? Any pics? 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • GTSBoy
      Can't put strut back

      By GTSBoy · Posted

      Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...