Jump to content
SAU Community

Recommended Posts

Recently ive been asked about correctly degreeing camshafts in RB engines, this step by step guide will hopefully answer a few questions and allow others to understand how its done and use this method to set up vernier cam gears to find exact lobe centers.

Cam gears help you to adjust your cams so that it opens and closes at the correct time. It also insures that maximum lift correspond to a desired crank position. The center line or the point on the cam where maximum lift occurs is known as lobe center.

Setting the cams to zero on the cam gear means absolutely nothing as different manufacturers of cams and cam belts can cause exact position of lobe centres to be slightly incorrect.

Lobe centers on the HKS 264's are 110 for the inlet cam and 103 for the exhaust cam. Adjusting your cams too these specs will most probably bring them very close to their maximum designed performance . A lobe center of 110 on the inlet cam means that maximum valve opening will be at 110º ATDC and 103 on the exhaust will mean that maximum valve lift will be at 103º BTDC.

This is how I degree my cams

1. Use a pencil, paper and arithmetic for this procedure, to keep track of the results.

2. Make a rigid pointer from stiff wire or an old coat hanger and attach it to the engine block. This pointer locates the degrees on the degree wheel.

3. With a degree wheel installed on the crankshaft, rotate the crank to get the no 1- piston at TDC and check to ensure that the valves are fully closed then adjust the pointer to zero (0º TDC) on the degree wheel.

4. Turn the crankshaft opposite the running rotation approximately 15-20 degrees. Install a dial indicator above the spark plug hole (i use a flat metal plate ive fabricated that bolts to the coil pack bracket holes) with the rod of the gauge going down the spark plug hole to check the position of number 1 piston.

5. Continue to turn the engine in the same direction until the piston comes back up and just touches the dial indicator. Make a note of the exact number on the degree wheel that the pointer is on.

6. Rotate the engine in the other direction (running rotation) until the piston comes back up and touches the dial indicator. Again note the number where the pointer is.

7. Remove the dial indicator and rotate the crankshaft to the midpoint of the two marks. At this point the piston is at the true top dead center. Loosen the degree wheel and adjust it so it will read 0º TDC at the pointer. Don't rotate the crankshaft to do this!

8. Now, it's time to locate the lobe centerline relative to TDC. Attach the dial indicator on the top of the head. Set the tip to contact the top of the no 1-cylinder inlet valve shim/bucket. Check to make sure that the indicator plunger is parallel to the valve stem. NOTE - any variance in an angle will produce geometric errors in the lift readings.

9. Rotate the engine in the normal direction of rotation until a reading on the dial gauge of 0.040 lift is reached. (Valve will start to open) Mark the dial gauge and make a note of the reading on the degree wheel.

10. Continue to turn the engine in the normal direction past maximum lift. The valve will now return to its close position. Make a note of the degree wheel reading when the indicator reads 0.040" on the return side

11. Now add the larger of the two readings that you noted on the degree wheel to 180 subtract the smaller number and then divide the answer by two. Your answer will indicate the lobe center of the cam. Example: open reading was 4 and close reading was 43. Now add 43 to 180 = 223, subtract 4 =219 divide by 2 = 109.5. Lobe center is 109.5 degrees.

12. Continue to move the cam on the adjustable cam gear and redo steps 10 to 12 until the required lobe center is achieved.

13. Now do the same for the exhaust cam

Hope this is not too complicated to follow.

cheers

Paul

Link to comment
https://www.sau.com.au/forums/topic/240804-degreeing-camshafts/
Share on other sites

  • 1 year later...

Hi Paul,

In my situation I am running a RB30 with RB25 Neo head, but I don't trust the timing markings on my car for a variety of reasons.

going from what you have mentioned above and the specs for standard RB25DET NEO Camshaft duration 236°in, 232°ex lift: 8.4mm in, 8.7mm ex

does any 1 know what degree's in relation to TDC the intake cam is set to standard @ 0.040" of lift? or what degree's the intake cam is set to at maximum lift in standard form.

regards

  • 2 weeks later...
  • 3 years later...

Im running a 30/26 my exhaust cam card says at .050 should be 242 deg and intake is 253 deg at .050. does this mean in stead of

(9. Rotate the engine in the normal direction of rotation until a reading on the dial gauge of 0.040” lift is reached. (Valve will start to open) Mark the dial gauge and make a note of the reading on the degree wheel.)

I should be reading .050 and not .040

No, the mark on the dial gauge is just a reference. Really you can use any number you like, so long as you use the same number for all your measurements. So say you choose 0.040" then you just rotate the engine forward until the gauge reads 0.040" again.

Should also note that for RB's you need to preload the dial indicator due to the lifter design in a cam on bucket setup.

Yes, the 0.050" on the cam card and its documented lift refer to the lift you should see at a specific crank angle.

Between these two points is the crankshaft position where maximum lift occurs, which is also where the advertised duration measurement should be.

No, the mark on the dial gauge is just a reference. Really you can use any number you like, so long as you use the same number for all your measurements. So say you choose 0.040" then you just rotate the engine forward until the gauge reads 0.040" again.

Should also note that for RB's you need to preload the dial indicator due to the lifter design in a cam on bucket setup.

Just want to correct myself here and apologise if I mislead anyone. I re-read Paul's write up and realised he was using a different method to the one I used. My bad.

So in this case, YES set the dial gauge for the valve lift indicated on the cam card.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It wasn't about the dollars. I mean how she didn't like the loud exhaust and you had to change it again 😛
    • I'll tell her I put in a new air filter on it, which, it would have anyway with the ITB's In the end she isn't to fussed, she spends lots of money on hair, nails, make-up and all the other "required" beauty products that women use, plus I grease the wheels with shiny gifts and holidays wherever and whenever I can She once questioned my car spending "budget", but after itemising everything she spends on herself, and what I spend on her, and the fact that I don't care if she does or doesn't wear make-up and fancy pants perfume, or requires new outfits for every wedding, funeral or anything else she deems worthy, and I'm quite happy to go "real" camping, instead of staying in hotels or jaunts on cruise ships, she decided not to press the subject on how I spend funds, and has never asked "how much did that cost" again, so a win to me And how often can you say you really get a win with the fairer sex? She is a good woman, and in the big picture, I'm really lucky.....that she hasn't killed me yet
    • What will you do when the Minister of War and Finance says the intake noises are too loud?
    • Will the clear coat dissolve the ink tho?? I thought about clear vinyl tape too. Thinking what to do haha. The one I have now is cracked in 1 spot, otherwise mint. Plus the MINES one is much thicker plastic material so its not flimsy at all.
    • No. Go a different colour, and just trim it at an edge line. Even manufacturers do different panels different colours etc.
×
×
  • Create New...