Jump to content
SAU Community

Recommended Posts

Yo, i was doing a 180 degree handbrake to spin my car (just bord muckin around) n then my car completely shut off.. i had to put it in drive and then i had to take the key and restart the engine to get it working again, why does that happen o_O

lol probably fuel surge... maybe ur handbrakey was too much for the amount of fuel u had in the tank and the pump ran dry which would cause the engine to obviously stop

my old car use to do that as well and also when doing donuts :P

when i was at driver dynamics defensive driving. We were given a chance to spin our car 180degree's on wet vinyl.

My car shut off also, clutch was all the way in too.

Ive heard from others that this happens to them too.

I dont think its fuel pump mounting/life related, its something else.

when i was at driver dynamics defensive driving. We were given a chance to spin our car 180degree's on wet vinyl.

My car shut off also, clutch was all the way in too.

Ive heard from others that this happens to them too.

I dont think its fuel pump mounting/life related, its something else.

Mine did it too, turned out it was the fuel pump :D

Hence i said that. Would do it even with 1/2 tank as it wasnt sitting right

Do jap cars have rollover protection which shuts off the fuel pump? I've heard of this in some cars... It could very well be the car think its rolling due to the massive change in g forces?

^^^^^

Yo, i was doing a 180 degree handbrake to spin my car (just bord muckin around) n then my car completely shut off.. i had to put it in drive and then i had to take the key and restart the engine to get it working again, why does that happen o_O

It's a fat-o-matic

i used to get this alot when i started drifting.. use the handbrake to get it to 90* then dump the clutch and gun it and hopefully it will hook up and spin you the rest of the way, if not, it will send you straight off the road.

i think the cars just go from lots of fuel, to no fuel.. think about it... your cruising at maybe 3-4000 rpm in 3rd, you knock it in to second in the revs rise, then you hit the handbrake and put the clutch in, which unless you keep the revs up, will drop it straight back down to idle very quickly... how many time in normal driving would you drive at 5-6000 rpm in second, and then all of a sudden do a foot shuffle and let the revs drop back to idle... our cars stall soo easily even slowly pulling up to the lights... let alone swinging it around 180*

cheers

Linton

never managed that one...

but definately dont think its to do with the above post... if that were the case it would also happen on a slow gear change.

not to mention clutching in after a burnout...

Are you guys being serious? automatic, which is like doing a handbrakey in a manual but not putting the clutch in.... you are stopping the driveline from spinning, which slows (stops) the engine from turning over, hence the stalling.... to those in a manual with same issue but you are pushing the cluch in, ignore this post.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...