Jump to content
SAU Community

Fitting A Vq30det Turbo On A Rb20det

ladams

By ladams,
in Engines & Forced Induction

 Share

Recommended Posts

ladams Apprentice

ladams

Posted
Posted

does any one know weather the turbo of a vq30det will go on a rb20det and if so what work has to be done to make it happen. one fell in to my lap and i am thinking of putting it on my ceffy? and how much power are they good for thanks for any answers.

Cheers

  • 3 months later...
limpus Mentor

limpus

Posted
Posted

The VQ30 turbo isn't a popular swap for the rb20 as yet...mainly because they aren't that common...how big is the exhaust housing though? if its meant for a 3L engine i suspect it might be too big for the rb20...top end should be decent though...but if a bit if lag doesn't bother you...go for it...it might start a revolution...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R34 gtt rb25det neo timing belt kit

      By Duncan · Posted

      No need to replace the cover if it is still intact (not worn through). It would be worth checking the balancer for matching marks on the rear, but I'd assume the balancer was loose at some stage. The cam timing marks look fine, once you put the new belt on you can only be right or a full tooth out
    • Duncan
      So i brought a boat...

      By Duncan · Posted

      Disconnecting rods! must have been an unpleasant surprise...
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
×
×
  • Create New...