Jump to content
SAU Community

Recommended Posts

Stock R33 bottom end before I rebuilt it (not due to failure of bottom end, just crank keyway) managed 352RWKW for ages no probs and reved her up to 8500rpm. Serviced it every 5000k and then 3000k's though, oil and filter.

600HP at the crank is a well known limit for a stock bottom end.

Rods are good for 400rwkw plus.

Pistons are pretty good, but will only take so much detonation/poor tuning before they fail.

Crank will take a lot, cars running up to 1000hp.

Oil pump and drive is a big problem with 32 cranks especially.

Blocks are good for a lot, unless bored out excessively, 1991,1992 had issues with cracking. N1 block (24U) is the serious block for big power...

Thats a quick rundown, other guys will add what I have missed. There is also a s%#t load of info when you do a search too.

Cheers.

Edited by GTRsean
Did you try the search button?

http://www.skylinesaustralia.com/forums/Po...+internals+rb26

There are plenty more threads where that came from too.

Please have a search around.

na i didnt even think about it, sorry guy and gals.

so with what i have read and researched 315kwatw is a safe power output for my `93` 32gtr?

the next stage of my car mods will be a engine rebuild but not for another 6-8 months (to raise funds), ive had garrett gt2860r turbos put on about 3 months ago and with them running at 40% ( about 10lb boost) the car still made 315kwatw, when they tuned it i told them i wanted it at a very safe level for standard internals but really when it comes down to it i have know idea whats on the inside, for all i know it could be chocka block full of jun parts.

and if anyone wants to know martin donnan tunes my car

cheers

Usage makes a huge difference my 32gtr let go on the track making 427 hp at the wheels on a stock bottom end

I suspect would still be kicking hard of it wasn't used on the track. No oil mods just a catch can and baffled rocker covers!

next on will have all the oil control mods under the sun. there is a huge thread on oil control mods for drift track on here just search

sydneykid started the thread I think.

Usage makes a huge difference my 32gtr let go on the track making 427 hp at the wheels on a stock bottom end

I suspect would still be kicking hard of it wasn't used on the track. No oil mods just a catch can and baffled rocker covers!

next on will have all the oil control mods under the sun. there is a huge thread on oil control mods for drift track on here just search

sydneykid started the thread I think.

i only use the car as a weekend cruz car, i havent had it on the track yet living in sa no one has much of a chance gettin their car on the track

Just wanting to know the limits of a rb26 before u should put forged internals in it, or what power has people got in their rb26 with standard internals, mine has 315kwatw.

we ran cats race car (r32 gtr engine with 100,000+ kms) at 340rwkw for 2 seasons in da before she killed it doing donuts :P

we ran cats race car (r32 gtr engine with 100,000+ kms) at 340rwkw for 2 seasons in da before she killed it doing donuts :)

I remember seeing her in da dvd serious performance 7; seemed so innocent but she will blow your bottom end.

ive spent around 20k... lol

Not bad mate; pretty much a whole car worth.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, im asking about this guy - coil igniter on rb25det series 1 r33 s1 engine. I need to know if pins on coil side indicate coils itself from 1-6 or it’s firing order so pin nr1 goes to 1st fired spark plug:(1pin-1firing spark, 2pin-5order firing spark, 3-3, 4-6, 5-2, 6-4…)   photo: https://files.fm/f/k9pdug38uq
    • Remove it. Certainly from the hub face. I'm not in love with leaving it on the wheel assembly surface either - but if it is common to do so, then....maybe fair enough. It's not difficult. Just time consuming. For the hub face you just need a large enough block and suitable grades of abrasive paper to get it off flat. The same would be true of the assembly face. Just more time consuming, probably needing a lot more care. It's defo going to be easier just to assemble the wheels as is, seal them up, and check them periodically to see if there's any movement or loosening of the fasteners, than it will be to remove it though.
    • Hello, I got my wheels powder coated and they've powder coated bloody everything the mating surface and hub (even told them not to lol) anyway should I leave it or remove it. (Would be very hard) I've searched a lot and lots of powder coaters don't mask the mating surface but do mask the hub surface. How bad it powder coat on the mating surface or hub? My question is what should I do?
    • Yeah, R34 with RB25DE likely has a 4AX01 box in it, which is a medium duty auto ~ with the RB25DET mill, it would've been fitted with 4AX00 (4AX13) heavy duty build (same case, different internals). An RB25DET will lunch on a medium duty 4R01 auto in pretty short order ...to give you some visual idea of differences between the 'medium' and 'heavy duty' boxes, you only have to look at the 2/4 band for comparison...it's chalk and cheese...(plus bigger high clutch, extra pinion in the planetary sets, higher oil pump output, different bearings, higher TC stall speed )... You can control them with just about any aftermarket TCU for electric-over 4-speed with TC lockup clutch (ie; the GM 4L60E and others)...I have a custom standalone TCU that includes MAP sensor (for turbo applications) along with TPS, RPM, and line pressure monitoring...in other words, I don't use any ECU signals...no real need to.
×
×
  • Create New...