Jump to content
SAU Community

Recommended Posts

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Head already in use on my other engine.

Willing to sell the complete bottom end for $400 will even throw in a standard plenum(minus fuel rail)

New OEM headgasket to sump. No pumps or alternator.

Has low comp in no. 5 cylinder.

Just needs a freshen up, whack in some forged pistons and your set.

RB25DET bottom end

2x standard plenums

1x standard complete fuel pump

Misc. bits and pieces

Take it all for $400

Need to clear some room!!!

  • 2 months later...

thanks mate about those lifters sorry dude im kinda new to this forum thing, dont laugh but what does PM mean. lol. and also have the lifters been sitting in an oil bath or are they still on the head itself. Ill pick them up or get you to send what ever suits you. id rather pick up though, if you havent sold them.

thanks mate about those lifters sorry dude im kinda new to this forum thing, dont laugh but what does PM mean. lol. and also have the lifters been sitting in an oil bath or are they still on the head itself. Ill pick them up or get you to send what ever suits you. id rather pick up though, if you havent sold them.

The lifters are sitting on a shelf in my garage (not in an oil bath)

They are still there so if you want to pick them up then thats fine.

  • 1 month later...

hey mate

still havent heard anything about those lifters mate. can you let me know who you sent them with so i can give them a call and see where it is. Sorry mate but i really need them or ele i wouldnt be busting balls. i was hoping to have them this weekend.

cheers

ayhan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...