Jump to content
SAU Community

Recommended Posts

After 6 years with this car, it's time we part ways. It has been always looked after and serviced every 5,000kms.

Truly in immaculate condition that has to been seen.

The engine was rebuilt with forged internals only 5,000kms ago.

The front and rear seats have been professionally retrimmed with tan leather. The car has been professinoaly lowered using whiteline suspension.

$12,480 with RWC PRICE DROP THIS PRICE IS ONLY VALID UNTIL NOV 8, after that it's going back up to 13.5k

For those who don't know what extra's you get in the rare LUXURY HIGH SPEC:

Sunroof

ABS

Front Lip + Side skirts + Spoiler (high spec body kit)

Fog Lights

Dual Air Bags

Premium Sound System (Which i've replaced)

S14a High Spec Luxury - Automatic with Shift Kit

Factory body kit, Dual air bags and Sunroof

*Performance Upgrades

-Rebuilt Engine with Forged Internals

-Front Mount Intercooler with a clever custom install so as to keep the factory fog lights

-Full 3" Exhaust with twin tip 3" Xforce muffler

-Pod Air Filter

-Cold Air Intake

-040 Bosch fuel pump

-Whiteline Suspension

-17" BEO Japanese Wheels

*Audio

-Pioneer MP3 Player

-Cadence & JL Speakers

*Accessories

-Rare genuine nismo clear indicators

-Genuine Nissan 200sx floor mats

-HKS Turbo Timer

-Boost Gauge

IMG_1511web.jpg

IMG_1537.jpg

IMG_1539.jpg

IMG_0167.jpg

4210824.jpg

4210786.jpg

*** THE200 Plates not included, can be purchased separately for $1,000. I will supply standard issue Victorian plates with the vehicle & RWC***

Call 0421139578

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...