Jump to content
SAU Community

Recommended Posts

Hello Everyone!

A few week ago I was looking at this D.I.Y >> http://www.skylinesaustralia.com/forums/To...mp;hl=stop+beep in the hope of stopping my beep - but this method only seems to work on <R33. So I opened up my baby and had a crack - and I succeeded! Very easy - very quick - and no damage to anything - it's just a simple disconnecting of a plug :)

I have Found no Side effects to any other system - I have a Auto Watch emob. and it still works fine - also this will not get rid of the beep for when you leave your lights on and open your door - also does not effect the door open lights on/off function

What you need:

RATCHET

10mm Socket

Phillips Head Screw Driver

Your Keys! <you will see why ;)

(Next 2 items are handy to have close if needed - but not essential)

Flat Head screw Driver (with double sided stick tape with one side still covered with plastic wrapping to stop sticking) < I use this to wedge open anything that is hard to open up - the double sticky tape prevents scratching because its spongy - very useful for when you need to take out air con vents on the R34 etc. as well.

And my trusty Victorinox Swiss Army Knife :)

t_0001139m_6e9c7b5.jpg

(CLICK ON PHOTOS FOR LARGE PICTURE)

Step 1: Unscrew Lower cover

t_0001138m_689594e.jpg

Left Hand Side of Lower Panel (Phillips head screw driver)

t_0001132m_8618887.jpg

Right Hand Side of Lower Panel (you will need 10mm socket)

t_0001130m_fe9c8bf.jpg

Here you will have to disconnect all Wires and thread them through any holes so you can remove the whole cover and put it out of the way

t_0001129m_73ab14c.jpg

Step 2: Unscrew Steering wheel under cover

t_0001127m_64f22cc.jpg

Open the Steering Wheel Adjustment Leave Right out so that it doesn't get in your way - also so that you can move the steering wheel up and down to help wiggle the case off

t_0001122m_be80390.jpg

Step 3: Remove the demand Beeperiser Plug

Your Undercover should look like this now - if not - you have gone astray and need to revert back to step 1 and/or you have the wrong car and revert back to top link!

t_0001118m_d25dda1.jpg

See that white plug well - Now you hear it!!

t_0001116m_559f008.jpg

Now you don't!! - Now just rap that sucker around some wires and make sure the little slider inside the plug is OFF - this is what your keys are for!! Before you go and put it all back together put the key in and make sure it is in the off position otherwise it will forever be beeping :(

t_0001115m_3ee528f.jpg

Enjoy the sweet sweet sound of beeplessness ;) and your stereo when you want to work on your car :)

If you need any help just post or Pm me :)

Aron

Link to comment
https://www.sau.com.au/forums/topic/242702-diy-stop-open-door-beep-for-r34/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That ring thing is interesting how it's holding everything together 
    • Hey guys. I have a 400R on its way to Australia from Japan currently and have a few questions I’m hoping others may be able to help with.   Wondering if anyone here has had any luck getting the Sat nav unit to work in Australia!? Assuming the Stereo is as simple as a band expanded and tv won’t work?  Seeing as they’re based off a Q50 which is Aus delivered is there any way to link that system to the nav? Nav modules and head unit are different part numbers and appear slightly different at the rear with plug ins etc. can I put my xtrail sd card into the rv37 and will that convert the maps or update to Australian? Has anyone got any advice here?     also has anyone fitted the factory remote start and Security system once it’s landed in Australia? I put an enquirey to Nissan Japan in via a third party, and they suggested it needs a Nissan Japan dealers device to setup and couldn’t guarantee if one here could do it or not. They can supply and I can physically fit it but to setup I would need a dealers device. Any information here would be appreciated also. I’ve seen one here with it fitted already prior to leaving Japan at a dealer/inporter, so clearly passes compliance and works when fitted Japan and doesn’t need changing here.      also, does the tyre inflation sensors work here? Does anything change with them when the vehicle arrives? Where are they actually situated? I’ve read they have batteries and they need to changing at times and seems like resetting involves the nav system?    any help here would be appreciated and any other aust specific information to help would be great. Looking forward to see what the current generation skyline is like and eager to see how many of the gadgets can be utilised here.  Thanks in advance 
    • Do need to take it with a pinch of salt. One of the adapter failures, they clearly had setup issues with the flywheel.  One of the slipping ones I spoke to and it was pretty clear the throwout was riding, rather than fix, just swapped to a new clutch.    These clutches are being put in anything from 5k offroad 4x4 beaters, GR yaris, 500hp commodores to 1200hp barra monsters. Bound to be some issues in some of them when they are not a simple bolt in affair due to the changes in height.    There is a lot going on in this picture and unless I did the job myself no way to tell what really happened. 
    • I did this mod in 2019  You just have to modify the top bracket of the ABS/TC/Fuel Pump Control ECU so it sits more upright and closer to the back seat and run a good quality positive battery lead from the engine bay, the negative lead i just bolted down to the body in the boot.
    • Damn... Not the feedback I want to hear.
×
×
  • Create New...