Jump to content
SAU Community

Recommended Posts

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

Along with checking the manifold flange for flatness, the t4 twin scroll gt35 atp housing I received had a lot of loose sitting slag deep inside the scrolls (out of sight). Worth thoroughly checking for the sake of the exhaust wheel.

Edited by DCIEVE

Is Sabbadin Automotive is doing the mechinical work for you?

Yes, we had the car transported down to Melbourne into Robs trusty hands for the engine build and to oversee the whole project.

Along with checking the manifold flange for flatness, the t4 twin scroll gt35 atp housing I received had a lot of loose sitting slag deep inside the scrolls (out of sight). Worth thoroughly checking for the sake of the exhaust wheel.

I'll make a note of checking that. The turbo is supplied from Full Race so I'm unsure if they are they same as ATP's?

More pieces coming in, it seems like it never ends...

The calculations we did for the new engine require an extra Bosch 044 and 1000cc injectors, so time to spend some time upgrading the whole system.

We have decided that the Tial MVS wastegates will not be water cooled (interested to hear peoples thoughts on this though), and that the run in tune will be 11psi with normal boost being set at 23psi. Interestingly the Tial MVS runs 3 springs to make the desired boost pressure, as compared to the usual one or two.

IMG_0314.jpg

IMG_0325.jpg

  • 1 month later...

New fuel system. One 044 with the standard pump acting as a lift wasn't going to cut it. Now twin 044 and a dedicated low volume lift pump to reduce heat build-up in the fuel. E85 Ready too ;)

fuel16.jpg

We have hit a hurdle lately with the wiring that has stopped the dash/heater controls/windows/speedo to stop working. (If only i could fine a body harness wiring diagram!!! :rant: ) If anyone has had anything similar please by all means let me know, as the issue is causing the alternator to stop charging and thus the car is basically unusable. We have tried several auto-elecs to help out with the issue but nobody seems to be willing to take on the challenge. If anyone knows someone that can lend a hand, please pass on my details to them.

  • 1 month later...
  • 2 weeks later...
  • 3 weeks later...

Finally got the car back in Sydney, the car has peformed very well and I'll try to go through all the stuff we have done over the last few weeks.

Needless to say, a severe lack of traction all the way to fourth gear, so some new sticky rubber will be the next thing on the list.

Looks the goods Dale, where did you get the polished fuse box cover? Do you guys sell them?

I bought it from the UK through a guy who made some in his spare time and sold them on eBay. Not sure if he is still doing them though.

We made some carbon fibre ones for a while, but they didn't sell very well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
×
×
  • Create New...