Jump to content
SAU Community

Recommended Posts

1/4 panels are the worse to do because u cant cut the paint anywhere so u blow it off in to the roof and u always going to be able to see it . if u try to buff it ( where it was blown off ) u 'll see it more the more u buff the worse it gets .when u paint any other panel u dont have that problem because u paint the whole panel , u cant do thwt with rear 1/4's as they dont have a finish .

riceee , it depends whats wrong with ur bonnet ( scrathed ,peeling, faded , damaged ? and remember if u need to paint colour near the guards u have to blend in to the guards so u nay have to paint 3 panels not just 1 . if the problem is in the centre of the bonnet then u blend to either side of it and clear the rest of the bonnet , u dont need to blend on the guards .

I have a Black Series 1 GTS-T and just got the bonnet and front guards and drivers side rear 1/4 done... the old paint and new paint even though it was the same colour stood out like a sore thumb.

I'm a perfectionist when it comes to the car and I have to get the doors and both other 1/4 done to get it looking right. I cutting the roof, boot and spoiler because they aren't in that bad a condition.

as long as the old paint is in good condition a good painter should be able to do a good match . u say its the same colour , how can it be the same colour ? unless the same painter painted the rest and had some paint left over it cant be the same .

when painters mix paint they have a formula that paint manufacturers give them and it tells them what colour tinters they have to use for a particular colour ( the car has the code on the id plate ) then they use a machine to accuratly disperse the amount of each tinter as per formula . ( some colours may have up to 7-8 diff tinters )

the end mix should be close to the paint in your car ( colour changes with age a little too ) now the painter has to eye match to bring it close enough so u cant tell the diff . metalic paint is easier because u can blend it and then clear the top , with solids ( none metalic or mica ,u cant do that ) so the match has to be a lot closer .

dont forget u get what u pay for though , dont expect to pay 200-300 to paint a bonnet and expect the painter to spend 1 hour to match the paint . in your case as u painted half the car they should have done a better job though .

  • 2 weeks later...

For anyone in Sydney, there's a guy called David who runs a mobile service for touching up scratches. I think he pretty much covers most of Sydney. I had a scratch on my bumper and he buffed it out and resprayed the whole bumper for $100. Looks perfect to me. Only thing is that he can't fix up metallic or pearl colours. My Skyline is just a flat red so he was able to do a really good job. His mobile is 0410 668 793.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not R7R. Meant to type R&R, obviously enough.
    • Bugger "making it look stock". I put one conventional internally fused Hella relay behind each globe. I just pulled the plugs off the back of the globes and built new loom segments with male and female plug parts to match up to the original loom and the globe, and used the original power wires to each globe coming from the switch through the original loom plug to trigger the relays. Ran a big fat (also separately fused) power wire across the front of the car to feed all the relays. It's as ugly as f**k, but it is wedged down between the headlight and battery on the RHS and the airbox and headlight on the LHS, and no-one ever looks in my engine bay, and on the odd occasion that they do I simply give no f**ks for what they think. Fully reversible - not that you'd ever want to. For f**k's sake. It's a Skyline. They made million of the bloody things. We've been crashing them into roadside furniture for 30 years now. There is a negative side effect to putting relays on the headlights. The coil current is too little to properly clean the contacts in the switches and they get blacked up and you have to open them up every couple of years and clean them manually. I have 25 years of experience on this point.
    • I was poking through the R34 wiring diagrams vs R33 and noticed that the R34 has proper headlight relays while the R33 is like the R32 and sends full headlight power through the headlight switch. I'm not afraid of wiring but I really would like to do this in a way that looks OEM (clipping into open positions on the OEM relay box) and also unlike the factory wiring which interlocks the high beam and low beam on the halogen series 1 GTR headlights I want to make it such that turning on the high beams keeps the low beams on as well. Any advice on how to locate the specific connectors + crimp terminals + relays I need? I was thinking one NO relay for low beams and another for combined high + low running off the factory high beam headlight connector. I don't really want to splice into a crusty old probably discontinued factory harness so fully reversible is my goal here.
    • Pretty sure they run the same engine as the Q50 hybrid which specifies 95 RON.  I ran 98 in mine for a while, but it made no difference in performance or economy, so I have been using 95 for the last few years.  I have never hit 6.0L/100km, but have returned mid to high 6 on the highway.  Being a hybrid, fuel economy is a lot more dependant on how you drive it.  At 110km/h, mine never goes into EV mode on the highway, so returns closer to 7.5L/100. urban driving can return low 8s if you are careful or over 10 if you are a bit more enthusiastic on the throttle.
    • About a quarter of what you want to do. It's only R7R, not R&dismantle&replaceparts&reassemble&R. ? It is stock. I already told you, you will NOT have broken those. It's f**king 4th gear for Christ's sake. You just chipped the teeth off.
×
×
  • Create New...