Jump to content
SAU Community

Recommended Posts

Hey all, my mum drives a a4 which recently needed new rotors,pads

after replacing the rotors "apparenly 4 times according to audi"

we found they had never been changed , spoke to some people who i dont need to name in cannington, who seemed good people and informed us, we got some lucas pads and brembo rotors put on,

the car made a slight click clunk kinda noise feeling when coming to a compleate stop, still does, how ever during this time mums driving the car down the grame farmer when the right hand rotor falls off and jams on and nearly sends the a4 onto the rong side of the road thru the tunnel = bang.

seemed like a simple thing breaks and rotors. ehh great

just be carefull guys... keep rolling

Link to comment
https://www.sau.com.au/forums/topic/24393-mums-audi-ate-shit/
Share on other sites

I've seen someone on another (unnamed) forum try to tell everyone that brakes are too important to do yourself and that you should leave it up to the "professionals". Whether changing rotors or pads or bleeding the system or reconditioning the calipers.

I've been doing my own brakes for over 15 years (the lot except the master cylinder, including reconditioning calipers) and I've never stuffed up like that. If you know what you're doing, can you really trust anyone other than yourself?

Buy new seals, push pistons out with compressed air (or take caliper off and pump the pedal until it comes out for the bush mechanic version), clean out inside of caliper, hone it if necessary, replace seals, re-assemble.

Repeat for other calipers, replace brake fluid and bleed system.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
    • New rear lights, filler panel sprayed, cleaned and back together    before, during, after shots 😍
    • 100% is gyprock, I agree. Slip of the keyboard. Haha! I left my indicator bulbs out to save a bit of weight.
×
×
  • Create New...