Jump to content
SAU Community

Recommended Posts

Rubbish!

Lets ignore LC for now. Ever been in an non TC car on grass and floored it? What happens? The wheels spin at a zillion miles an hour. What happens when you come off of the grass and back onto the road? There is a massive load as those high spinning wheels re-grip. If the car had TC on however you'd never had got those huge spinning wheels on the grass and then no massive load when you grip back up. And how about going from a wet surface to a dry one?

Now back to LC. Who says that feature that is being used as LC was actually meant to be that? It's not in any manuals I've seen or heard about. It may just be a lower rpm rev cut due to the fact the car is stationary and consequently not getting any cooling. And people are just mis-using this feature to create a type of LC. I dunno. Either way like the above situations it puts pressures on drive-trains that wouldn't occur had VDC been switched on.

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

So.......after this whole thread, why dont more people run out and get JDM ones?

Its not like they're not available. You also get a definate price and definate delivery price (eg, pay now, take it home straight away). Except in case of being concerned and requiring warranty, finance not being approved for low volume imports etc

Nissan, thankfully for current GTR owners like myself just waiting for the prices to fall a bit, are leaving it quite late to get on the compliance bandwagon

So nissan dont want you machining the discs? Ouch. Thats going to hurt the old wallet at service time

DOT4 only for brake fluid?!

Hill start assist is a nice touch though, Subaru Liberties have had that for a while

So.......after this whole thread, why dont more people run out and get JDM ones?

Its not like they're not available. You also get a definate price and definate delivery price (eg, pay now, take it home straight away). Except in case of being concerned and requiring warranty, finance not being approved for low volume imports etc

Nissan, thankfully for current GTR owners like myself just waiting for the prices to fall a bit, are leaving it quite late to get on the compliance bandwagon

It could have something to do with the souring exchange rate bumping the price of the JDM ones up by about $40K. It's actually cheaper to get one from Nissan.

Edited by Iron Chef
So.......after this whole thread, why dont more people run out and get JDM ones?

I'm going to guesstimate that those who are using them as road cars are going to want a warranty and dealer support if they're putting down $150K. Maybe they've never been to a Nissan stealership, and realised how little you're actually getting from them. :D

People who are able to pay the asking price, and then modify / race them, pretty much already have done so.

Nissan, thankfully for current GTR owners like myself just waiting for the prices to fall a bit, are leaving it quite late to get on the compliance bandwagon

I dunno about that. Nissan didn't have them ready for local sale when the Aussie dollar was doing a roaring trade against the Yen, which would have been the perfect time to bring in a car this expensive. I'm not sure if they're "leaving it late", or just procrastinating because they're lazy, or some other reason.

It could have something to do with the souring exchange rate bumping the price of the JDM ones up by about $40K. It's actually cheaper to get one from Nissan.

I agree with your point about the exchange rate, but as far as buying them from Nissan, we'll have to see what they end up coming in at :)

I'm going to guesstimate that those who are using them as road cars are going to want a warranty and dealer support if they're putting down $150K. Maybe they've never been to a Nissan stealership, and realised how little you're actually getting from them. :blink:

People who are able to pay the asking price, and then modify / race them, pretty much already have done so.

I dunno about that. Nissan didn't have them ready for local sale when the Aussie dollar was doing a roaring trade against the Yen, which would have been the perfect time to bring in a car this expensive. I'm not sure if they're "leaving it late", or just procrastinating because they're lazy, or some other reason.

Leaving it late is leaving it late mate, my fingers are crossed they miss the boat, so to speak :D

I suspect if they're announcing on-road prices, they would've been smart enough to lock in exchange rates and purchased their yen back when the dollar was strong. If they didn't, they'll be losing on every GT-R they sell if the RRP doesn't change.

But yes, Nissan haven't left much of a gap in their 18-month window before used ones become eligible...

Edited by Iron Chef

well the R35 that I have coming was paid for earlier this year, so even though it's only being imported now, it will be sold at effectively the old rate, so some lucky person will get to capitalise on the fact that we bought the yen to pay for it months ago. if it was being paid for now I'd say it would cost over $220K. I think most importers will do the same as me if they can and do the right thnig and sell them at the 'old rate' as it won't be viable any other way.

A question to you guys that know importing better than i do, what would be the latest nissan could start the compliance approval proceedings and get it done in time?

I know compliance is taking ages currently, but lets say for argument sake, that compliance are at their usual pace of work :ninja:

Good fortune has indeed smiled on you, my friend - I envy the lucky bugger who buys it off you!

so do I! in the meantime all I can do is look longingly at the keys for it dangling off my key hook. :)

Officially neither does the EVO X SST nor the DSG VW's - but all of them if you know the right button sequences will activate the Launch Control. This will not be mentioned in ANY of the operating manuals by any of those companies but that doesn't mean that it isnt there - it is just not listed as "a standard feature" and they will refuse to admit its existence.

But as I already mentioned they state that "The use & descriptions of this type of procedure being outlined in the testing and reviews is not endorsed by Nissan" which means it will still be there. And they also state that turning the VDC off will void your warranty so therefore should you do it and break the car its your problem.

Put simply if they say the car doesn't have launch control (or should I say not reference that it does have it) they don't have to then say "it has launch control but you can't use it".

I am almost certain that there is instructions in my DSG golf on how to use the launch control, or some form of it. I will try remember to get a picture of it tonight.

So nissan dont want you machining the discs? Ouch. Thats going to hurt the old wallet at service time

DOT4 only for brake fluid?!

Hill start assist is a nice touch though, Subaru Liberties have had that for a while

That's a standard function for DSG's - the clutches take up when you get off the brake.

  • 4 weeks later...
Fair enough, my arguement still stands, IF Nissan had released a manual gearbox, i dont think there would have been many issues. Alright maybe blowing the clutch at most due to improper bedding etc, but Nissan would bed it before anyhow. Sure it maybe a few 10ths slower but it would still have a manual, which would be lighter then the heavy auto, cheaper to replace, and be more interactive and fun to drive.

But hey, thats just my 2c

Whats so good about a manual gearbox??? This has all the benefits of a manual plus the benefits of an automatic (without the drawbacks ie. torque convertor). Do you really miss having a clutch that much? Did you only just get your licence and using a clutch is still a novelty to you?

i think one of the reasons the GT-R is so quick is because of the box, think about how many gear changes you would have, say at the nurburgring, (i think around 70) and how much quicker those paddle shifts are relative to manually changing. There would be a tenth or two advantage in every gearchange. It all adds up i reckon..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...