Jump to content
SAU Community

Recommended Posts

Originally posted by R33man

I was recently quoted $4000 for supply and fit (including dyno tune) of a Power FC computer and boost controller.  Is this a good price or should i look elsewhere.  :)

:bahaha: can u say RIP OFF??

U can buy one new for $1400 with hand controller, to install takes about 10 mins if u know how to use a screw driver and socket set. Proper tune depending on mods you got about 2 hrs.

All up i think u are paying around $2300 more than u should.

Link to comment
https://www.sau.com.au/forums/topic/24467-power-fc-cost/#findComment-523164
Share on other sites

Originally posted by Ronin 09

look out guys, customs are getting smart. The last 2 packages from greenline i've received have been taxed, and they've somehow got the exact cost of the items as per greenline's site...

How much tax did u pay on the parts??

Customs must be reading the forums to now.

Link to comment
https://www.sau.com.au/forums/topic/24467-power-fc-cost/#findComment-524328
Share on other sites

Originally posted by hungry6

mine is costing me a fair bit more to tunecause i'm looking for the every last horses in the motor , including the one hiding behing the trees.

One word : DETONATION.

If you try and extract evey last pony, as soon as the air temp changes, or you get a slightly off batch of fuel etc, your check engine light starts flashing away at you, ignore it and do a rebuild.

Its a real pain (talking from experience). If you go for a more conservative tune, it is more likely to give you a longer, hassell free life.

0.02

Link to comment
https://www.sau.com.au/forums/topic/24467-power-fc-cost/#findComment-524718
Share on other sites

Steve...of course detonation and exhaust temp would be taken into consideration. In fact a lot time is usually spent tuning at the track (if the pockets are deep) where temp is hot and car is being pushed hard...would have thought you had done that with your car too.

P.S....why would you ignore the engine light flashing at you?

Link to comment
https://www.sau.com.au/forums/topic/24467-power-fc-cost/#findComment-525269
Share on other sites

4 Doorz, the post just set off alarm bells, so injecting a word of caution. Every last pony insights visions of max hp on a dyno - to me anyways. I had someone do a 'get every pony possible' tune, and it wasnt long before I took it somewhere else and got a retune.

I completely agree with you, WRT a good tune. My car doesnt get track tuned, but it does get a good workout on the street. And yes it does cost extra, but well worth it IMHO.

Check engine light - some people dont keep an eye on their check engine light, and usually pay the price.

Link to comment
https://www.sau.com.au/forums/topic/24467-power-fc-cost/#findComment-525658
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is there a diameter difference in the stock to Nismo? If so, the weight alone won't be indicative when comparing flywheels of the same diameter, since the radius of the flywheel acts on the moment of inertia with a square factor, where as mass is linear. Roughly going from a 4.5kg flywheel with radius 20cm, to a 9kg flywheel with radius 14cm would see them act the same. This calc is just here to act as a brief numbers comparison and reflects no actual RB flywheel diameters etc. it also assumes even weight distribution (thickness) throughout.
    • It seems this could be due to a restructure/team direction change... Or... You're working with a different category of vehicle... Or you've decided you'd rather be able to play with your own cars again...   I'm hoping the latter...
    • had 4 weeks off over xmas and well did some stuff to the shed and BRZ, well short of is I don't work full time in supercars anymore as of yesterday.........
    • Did you get any down time over Christmas, or have you had any since to play with this? Or have you given up and are trying to get yourself a second hand V8SC instead?
    • A random thought I had just before I hit "Submit on this post". If brake fluid, in a container in my garage that has never been opened goes bad after 18 months, why can I leave it in my car for 24 months in an "unsealed container"... Secondly, some other digging, and brake fluid manufacturers seem to be saying 5 year shelf life... Me thinks there line on 18 months for an unsealed bottle is pretty much horse shit marketing spin. Kind of like how if you drive a car and don't run a turbo timer your turbo and motor will die horribly...   Where I started on this though... Someone (me) started down a bit of a rabbit hole, I don't quite have the proper equipment to do Equilibrium Reflux boiling per the proper test standards. I did a little digging on YouTube, and this was the first video I found on someone attempting to "just boil it". This video isn't overly scientific, as we don't have a known reference for his test either. Inaccuracy in his equipment could have him reaching the 460 to 470f boiling point range in reality. In the video, using a laser temp gun, he claims his Dot3 that's been open in his florida garage for over a year gets to about 420 to 430 fahrenheit (215 to 221c) Doing some googling, I located an MSDS for that specific oil, and from new, it claims a dry boiling point of 460 to 470f. Unfortunately they don't list a wet boiling point for us to see how far it degraded toward its "wet" point. While watching it I was thinking "I wonder what the flash point is..." turns out its only 480f for that specific brake fluid....   As for testing the oil's resistance, I might not be able to accurately do that unfortunately. Resistance level will be quite a LOT higher than my system can read I suspect based on some research. However, I might be able to do it by measuring the current when I apply a specific voltage. I won't have an actual water % value, but I'll have some values I can compare between the multitude of fluids. I'll run some vague calculations later and see if I should be able to read any reliable amount of current. These calcs will be based on some values I've found for other oils, and see how close I'll need my terminals together. From memory I can get down to 1pA accuracy on the DMM. I don't think my IOT Power Tester has any better resolution.    
×
×
  • Create New...