Jump to content
SAU Community

Recommended Posts

I have these Apexi parts for sale. They are brand new and come with a warranty

£´£±£´¡Ý£Î£°£²£¹¡¡¡¡¡¡ 1 X BNR32 33 PFC H/C 415 X001

£´£±£´¡Ý£Î£°£±£¸¡¡¡¡¡¡ 3 X S15 PFC H/C 415 X001

£´£±£´¡Ý£Î£°£±£µ¡¡¡¡¡¡ 1 X RPS 13 94 - 96 PFC H/C 415 X001

All $1354 AUS each Delivered PFC and the H/C

Apexi 8 X RSM`S $281 each delivered

Apexi 8 X SAFC 2 $420 each delivered

Link to comment
https://www.sau.com.au/forums/topic/24494-hello-fellow-west-austrailans/
Share on other sites

Originally posted by nengun

I have these Apexi parts for sale. They are brand new and come with a warranty  

£´£±£´¡Ý£Î£°£²£¹¡¡¡¡¡¡ 1 X BNR32 33 PFC H/C 415 X001  

£´£±£´¡Ý£Î£°£±£¸¡¡¡¡¡¡ 3 X S15 PFC H/C 415 X001  

£´£±£´¡Ý£Î£°£±£µ¡¡¡¡¡¡ 1 X RPS 13 94 - 96 PFC H/C 415 X001  

All $1354 AUS each Delivered PFC and the H/C  

Apexi 8 X RSM`S $281 each delivered  

Apexi 8 X SAFC 2 $420 each delivered  

Please contact [email protected]

I need to fix up my translater, I cant read any of the stuff before all the model numbers. Is this the same with others?????

:headshot:

OK around 1350 to my door.... brand new and everything... now here comes my newbie question... this is very embarrasing the "BNR32 33" part ... is that saying R33 or R32 or just an R32...

I am confused but interested :)

This Thread should not be in here,,,It's a Business Section posting that requires a Donation to PranK.

Thread locked till Further Notice.

Neil.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...