Jump to content
SAU Community

Recommended Posts

just high flow it. not much more lag than std, and mines pushing 250rwhp at 1bar. thats got the afm maxed, the injectors are prob on the edge too being a red top. strangely the std fuel pump still has some left, unless it was modified in jp. can be done for around 1k or another option is the rb25 unit with similar results but ceramic exh so itll be on the limit

A HKS2530 will give you "Plenty of performance" - around 210-230rwks

Beyond that it cost substantial $$$. What $$$ are you realistically looking at spending on just turbo???

I would love to see what a properly setup HKS2835 with manifold/wastegate/ECU/injectors/AFM would do on an RB20.

A Trust TD06L2-20G-8cm kit with manifold/wastegate is about as big as id go, any bigger and boost response may be compromised a little too much. (Lag in negligible, with boost response bumped up about 1200-1500rpm)

  • 9 years later...

wat's the best turbo for the rb20det, without too much lag, fuel cut etc. and with plenty of performance??????? :burnout:

n e ideas or info wuld b much appreciated

a garrett 2871r would be in the range, a 0.63 rear housing and cranked up to 18-20psi with possibly some E85 to make it come alive even more..

there common on sr20's from what ive seen/read.

How much power are you aiming for?

They have nothing before 4 grand anyway just get a TD06L2 20G 8cm (like $799 from the kando or a billet one from hypergear), a few people have said they have moved from something like a 2530 to something larger and not noticed much difference.

But it depends what you want if you want a whole highmount setup or if you want to keep it as stock looking as possible etc etc.

You mentioned fuel cut. There's no point upgrading the ECU if you're not going to remap or Nistune the ECU at least. I'd go a Garrett GTX3067R with an ATP divided .82 housing on stock manifold modded for external gate.

That would be quite disgusting to drive until 6000. Divided housing then put it on a stock manifold, not really that helpful there

Divided housing then put it on a stock manifold, not really that helpful there

I'm assuming RB20 manifolds are the same as RB25 ones and are divided (other than the 5mm gap which can be welded up)? Why would it be disgusting until 6000? Stock manifold will have better response than aftermarket. I am referring to the new smaller GTX3067R, not a typo of a GTX3076R. The divided .82 housing has better response than an open .63. This setup would be more responsive than a GT-RS/GT2871R with the right tuning and cam gears with a fair bit more top-end potential. Why would this be discusting until 6000? Disgusting on tyres I guess haha. Edited by bradsm87

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 65601-05U00 is the hood latch. 62550-08U31 is the support that holds it to the radiator core support. They are all super discontinued so I don't really have any great leads on how to source this stuff.
    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
×
×
  • Create New...