Jump to content
SAU Community

Recommended Posts

post-28740-1227011236_thumb.jpg

this is my ehxhaust.

From the cat there are 2 mufflers in line, one closer to the cat and on near the tip as you can see in the pic.

If i removed one ( probably the one closer to the cat) will I get a deeper note or will it be excessively loud and drony..

At the moment it is a relatively quite exhaust but has a nice subtle note.

Also is there any performance gains to be had by removing a muufler. Just by looking at pictures of some

exhausts for sale, most seem to have only 1 muffler in line from the cat.

Or is this just a totally ridiculous idea that wont work????

cheers

loc

Link to comment
https://www.sau.com.au/forums/topic/245431-nismo-exhaust/
Share on other sites

If you remove the centre muffler it will make the exhaust a lot louder. Unless you're aiming for big power numbers i wouldn't bother, it will just attract more attention from the police for very little gain.

The Nismo exhausts are good because they are quiet and free flowing. I have one on my car and it's awesome except for the rediculous carbon tip :D

Link to comment
https://www.sau.com.au/forums/topic/245431-nismo-exhaust/#findComment-4269847
Share on other sites

I removed the resinator on my exhaust so it is now 3 1/2 inch from turbo through to high flow cat to x-force cannon with 5 inch tip. Mine sounded noticably louder when i had the resinator taken out, mine didnt have any drone, sounds deeper and great. But like stokesy said above, there are very minimal gains, it just makes ur exhaust louder. It does sound good though!!!

Link to comment
https://www.sau.com.au/forums/topic/245431-nismo-exhaust/#findComment-4270454
Share on other sites

And destroying something Nismo is insulting :D

I had a Mugen Twinloop on my old Integra Type R, everyone said the twinloops are so restrictive blah blah.. but, unbolting it and just running it with the mid section lost power and torque all over the rev range. Pretty much running a 2.5" straight through. Dyno tested back to back!

Generally speaking companies like that know what they are doing :P

Link to comment
https://www.sau.com.au/forums/topic/245431-nismo-exhaust/#findComment-4271541
Share on other sites

cool thanks for the replies.

Power gains is not really what im after, more so a stronger sound without it sounding ridiculously loud

i'm still undecided what to do but as gotRICE said i would be reluctant to destroy anything nismo

Link to comment
https://www.sau.com.au/forums/topic/245431-nismo-exhaust/#findComment-4271919
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...