Jump to content
SAU Community

Recommended Posts

hey everyone.

im stripping parts off my r34 to return to stock.

here are the parts i have for sale.

apexi power fc with hand controller for r34 gtt, the power fc is used, but good condition. the hand controller is brand new, no scratches etc. looking for $1300ono. (in box)

apexi power fc hand controller for r33 gtst, hand controller is in good condition. looking for $350ono.

hks in, ex cam gears (purple) for r34gtt. think they also fit r33? good condition, looking for $350ono the pair. (in box)

momo pedal set, brand new, looking for $50ono. (in box)

nismo gearknob (chrome type) very very light scratches, barely noticeable. looking for $60ono. (in box)

r33 series 2 gearbox conversion, also can fit r34. comes with gearbox approx 80,000kms, has c's short shifter, hd exedy clutch (used), slave cyl, pressure plate etc. looking for $1700ono.

r34 manual gear surround, good condition, could use a spray, looking for $150ono.

19" chrome impul starcorp rims, wide pack, 19x8.5, 19x9.5. rear tyres and 1 front tyre have approx 85% tread, 1 front tyre has a bit of camber wear but other tread is good. slight gutter rash, looking for $1250ono.

thats all im looking at selling for the moment guys, will be adding more stuff soon.

for those interested, pm me and i can also supply pictures for those interested.

cheers guys

Link to comment
https://www.sau.com.au/forums/topic/245536-r3433-gtt-car-parts-for-sale/
Share on other sites

also about the gearbox, i really need to sell the whole thing as is (a conversion) as it'll be hard to sell the other parts, if theres a buyer for all parts. then i will split it up.

the gearknob pics will be up this weekend with the cam gears etc.

no stock gearknob sorry mate.

cheers.

hey everyone, sorry about the late replies.

the rims and power fc are sold.

here are pics of the cam gears and gearknob, also yes the cam gears will fit an r33 gtst. in and ex.

and all pms replied.

cheers.

post-48744-1228277970_thumb.jpg

here are pics of the cam gears and gearknob, also yes the cam gears will fit an r33 gtst. in and ex.

Sorry mate just to let you know those wont fit a GTT or a GTST on the intake you can go through the process of removing the VCT but will also require an aftermarket or modified RB26 camshaft to install

They are a strait swap for all GTR RB26 motors though

And they are the old version cam gears too ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...