Jump to content
SAU Community

Gt35r Vs Garrett T04z - Discussion (just Post In This Thread To Create A Database)


Recommended Posts

My tuner (Ant Scali) has only just returned from Mt Buller.

He was working with Steve on the r35 development.

My car WILL be tuned Friday arvo.... then I will post up results as soon as possible.

26 with .84 T04Z

13065_226473479702_508809702_4240776_6507335_n.jpg

20 psi with little timing.

Just picked up the car, were doing some more mapping tonight. 4th gear pulls.

Doesn't feel to bad, mind you I have yet to have a proper drive of it.. Everytime I try to make a rationed opinion the adrenaline kicks in and I forget to keep an eye on how responsive it is.. lol..

Fix that boost control :D

If you can get it to pull to 21psi much sooner it'll be interesting to see what happens before/after.

So yes... that means get the graphs overlapped when you do :)

Funnily enough, almost a carbon copy of the one just above.

On a preliminary tune, it went 540rwhp (~400rwkw) at 19psi. Quite a bit lazier than the 35R though. On the same dyno, the 35R went 510rwhp on 26psi.

Am changing boost controller (as we weren't impressed with it's ability to hold boost) and tuning for 25psi next week. When that's done we'll print out a graph overlapping the 35R run with the T04Z run and I'll post it up.

Edited by Brockas

Sweet, sounds good, what boost controller did u have in it.

ya didnt think the Z could defy human nature with response. but will be interesting to see the true outcome and how fare apart they are.

Edited by nigel

Yeh at this stage it looks like it's going to be about 500rpm difference, but I believe the area under the curve will be greater with the Z.

I had a Greddy Profec B II, and I've just ordered a Blitz Dual SBC Spec-R.

Nar, overlapped Scatalotto's. His tromped mine everywhere, but we'll see how it goes with the new boost controller and some cam timing adjustments.

26 with .84 T04Z

13065_226473479702_508809702_4240776_6507335_n.jpg

20 psi with little timing.

Just picked up the car, were doing some more mapping tonight. 4th gear pulls.

Doesn't feel to bad, mind you I have yet to have a proper drive of it.. Everytime I try to make a rationed opinion the adrenaline kicks in and I forget to keep an eye on how responsive it is.. lol..

Did Paul tune your car? Is that the Twin scroll or just a single entry? Have to let me know how responsive it is etc

I've had fairly good results using the GT35...

Thinking of going to a GT37 or GT40 when i do a 3L bottom end...

car wasn't running it's best on the day of the dyno either...

post-27540-1261453111_thumb.jpg

Ok, mine went 580rwhp today.

Will pick it up and scan dyno sheet tomorrow.

Keen to see a comparison vs your gt35.

what boost to make 580rwhp?

How much longer (RPM) to reach full boost than gt35?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeh... literally every time i jump on a forum, see an instagram post or see an engine bay at a car show, i get an idea and add it to my 'to do' list. So what started off as, hey can u just make a couple of intake hard pipes because my dumbass bought the wrong apexi kit, blew out into a 2 week job including braided brake lines & custom bash kit for the front lip haha.  Getting Luke from A4E engineering to make a full custom exhaust with a controllable aes dump valve so i can actually switch between quiet and loud, because right now its just loud all day every day. Then after that go and get the tune redone flex e85 & 98 as i get bugger all milage from e85, makes going for longer drivers difficult
    • Car looks clean as. You ended up getting quite a bit done 馃槀  So what's the plan for the exhaust? 
    • The only Neo rods that were any different to any other RB25 rods were the DET ones, and they were the same as RB26. Here is a Neo DET rod. O5U part number visible. Here is a post in a thread here on SAU with evidence from someone who has done this before. There are photos in the thread of normal RB25 rods.  
    • Sure, but why assume that will be the case forever? And why assume you'll be able to do an oil change to swap back to a stock drain bolt before that happens? And does it even matter when I change the oil at fairly short intervals? Life can be funny sometimes and unexpected things can happen. Like breaking a collarbone so you can't do any work on your car for a few months but the oil change is due so you have to take it to somewhere and hope they don't do something stupid like stacking the new drain plug washer on top of the old one.
    • Do u know how to identify the rods are rb25 or neo ones? Can u look into the pics and tell me is they de or de neo ones. Its confusing becoz my motor has de neo head but block is 25de 75t, so really confusing me about rods, crank.
  • Create New...