Jump to content
SAU Community

Recommended Posts

  • Replies 157
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Gemma

Jeff

Andrew

Mitch- figjam

James- j4m35

Vicky

Eliiot- Palmer

Jason- Gizzmo

blk180

pete- sexy pete

shawn- darkon

anna34

shane

dave- wisey18

jay- Jay Stylz

scott- scottie

rafael- pbk1776

dale- silver bullet

michael-micor

Alien

Daniel- Punisher6942

76

Radz

Kaan

Richieb

col- JapVLR32

lankanboiiR34

Jason-FLN75S

Davis-Aggroman

Brian- bt23

cool good turn out so far even with some of these ppl are maybes

GRRRRRR JEEEFFFFFFFF!!!!!!! You have to come. Wont be the same with out you!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Damn it, just realised I'm going to need to get an E-TAG before the cruise so I can get back across the cashless bridge! :<

How long do you guys think it will take to get from Chatswood to Liverpool?

Damn it, just realised I'm going to need to get an E-TAG before the cruise so I can get back across the cashless bridge! :<

How long do you guys think it will take to get from Chatswood to Liverpool?

hmm if you do an M5 run probably about 30 - 40 mins

Is there generally much police action on these runs? Just out of curiosity. One would assume a pack of Skylines would be quite the eye opener.

Excellent question there man, this would be my first time and nice to know




  • Similar Content

  • Latest Posts

    • Donut tried them out, they were fine as long as the bolt or nut wasn’t very tight 
    • It is a very complicated plastic tank. Sitting between the rear seats and the rear subframe. Requires a siphon venturi pump in the hat to suck the fuel from the passenger side to the driver side of the tank. The answer is probably prepping the tank very carefully to eliminate all fuel fumes, drilling any cracks to stop propagation, then plastic weld. I don't really see any other solution here. 
    • Does anyone know when your oil drops viscosity, if it is an issue? I imagine with tuned cars they will be overfueling more compared to a stock standard car and will thin out over time. 
    • anyone ever used these ? https://www.ebay.com.au/itm/186214260439?_skw=socket+set&itmmeta=01JEG3TKV388ZXGP8N7CHNCQ45&hash=item2b5b3c1ed7:g:mhAAAOSwwB9lf~Xm&itmprp=enc%3AAQAJAAAAwHoV3kP08IDx%2BKZ9MfhVJKkJwJeiNMm%2FsStacz%2BhjzBowaFnbNCowwe08vVGrW0FbesCs%2Flw%2FQYjDQLjKsuKvgysWT9%2F4b9AZUX3qLP5RDfFhtD8DxufvqBbyZrQAQXuG3h8%2BxxqhWhH8fIfU84eA9W7VIpxDNw9MWj9BdfkkMasYhcqOjTrcKwLyD3ftzZbaZb2Us7%2FFR1Q2kcT68ZYRU77%2F%2BtRr1qBS27BXxh%2FjWBQxhWyUcLlEFIb%2BITZPIKwxQ%3D%3D|tkp%3ABlBMUOy96oP0ZA   I believe the idea being, the rods push back around the shape of whatever nut you put in there. Sounds pretty handy to just need to carry 1x socket in the car for 'most sizes'  but, theory vs reality, anyone tried them?
    • I'm not that familiar with R33 tanks. Plastic? Up behind the rear seat between the towers? Or under the boot floor like a normal car? It's the battery that's up between the towers isn't it? So, plastic tanks. Well, um. The obvious reco is plastic welding, which you'd only look at asking someone who's really good at to contemplate trying. The fuel contamination and grot is probably going to make it quite difficult though. Whether plastic or steel - the end of the crack will want to be drilled before any welding or sealing is done. Otherwise it will just continue to wander along until something bad happens. Steel tank? The obvious answer is drain, wash, purge with inert gas and drill the crack end and weld/braze/silver solder/whatever the guys who do that to fuel tanks recommend. I had a crack/hole/leak in the bottom of a Commodore tank (oe was it my ALFA? - can't remember) that I slammed some gorilla snot onto and it never leaked again. It worked surprisingly well. Or, it's time to fab a new tank.
×
×
  • Create New...