Jump to content
SAU Community

Recommended Posts

hey peeps

i hav no idea wat this one button is for in my R33, the car didnt come wit the complete version of users manual, therefore i dunno the function of this particular button. chek out the attached photo and tel me wat it is if u guys know.

cheeers ppl

Dude that's your ariel up and down

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4285433
Share on other sites

I've got one of these buttons too. As far as I'm aware, it doesn't do anything. I couldn't figure it out either. When I pulled apart my dash i noted that the button was located near a little vent that was attached to a hose of some kind. Almost like an air freshener pump. I presumed it was for that reason.

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4285550
Share on other sites

I've got one of these buttons too. As far as I'm aware, it doesn't do anything. I couldn't figure it out either. When I pulled apart my dash i noted that the button was located near a little vent that was attached to a hose of some kind. Almost like an air freshener pump. I presumed it was for that reason.

I believe that hose is a temperature sensor of sorts

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4287222
Share on other sites

that was a compliance issue under the old rules... the cars needed a dimmer switch and that was the easiest way to put one in :(

and i always thought it was factory cause it sure looks like it. my antenna switch is just above my left knee..that looks factory too. thumbs up to the compliance guys then.

yeah the tube is for your climate control to measure cabin temp, im pretty sure of it.

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4287459
Share on other sites

Some jealous so-and-sos buried a really smic R33 with its owner out at Eastern Creek... right in the middle of the Lighthorse Interchange.

You cannot see the car at all. The only way he was able to draw attention, was to press this switch!

All that remains, is this aerial, sticking up outta the ground; 50m high & lit up at night!

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4296807
Share on other sites

  • 1 month later...
hey peeps

i hav no idea wat this one button is for in my R33, the car didnt come wit the complete version of users manual, therefore i dunno the function of this particular button. chek out the attached photo and tel me wat it is if u guys know.

cheeers ppl

It Activates The Flux Capacitor. And When You Hit 88 MPH *BLAMMMM*

Link to comment
https://www.sau.com.au/forums/topic/246538-r33/#findComment-4360633
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Finally had these painted and fitted and pleased with the result. also managed to source 400R fender badges.    
    • who can tell me what this is and why my car talks to me? i think it's hilarious. it's on my r34 right above the drivers-side storage compartment. the characters under the wrench say "inspection". every 10 or 20 startups, a voice starts talking in japanese from some speaker in this area below the dashboard. it says a few sentences then shuts off. different from the ETC card reader voice that happens every time i start the car. I've never found the speaker, i've never been able to catch the voice and translate what it says, and i've never found a forum thread that tells me how to reset the warnings. the holes in between the symbols are NOT buttons you can press to reset the warnings. anyone else have this? has the demon lord from Hereditary infected my car?!
    • Would you ever vent this bonnet or will it be unnecessary?
    • Happy new years folks! Wishing you all a successful year of money pit ownership!  So the subframe bushes are out....   Ok, who else has done that job before??  What a C U Next Tuesday of a job that is!  Be glad to not do that again in a hurry! I think I explored every option available to chop the middle section of the bushes out, most of them unsuccessfully! I tried a holesaw, die grinder, normal drill bit, air chisel, etc, etc. The true success happened by accident when I'd decided to try a step drill I spotted on the bench on the way passed.  See, there are benefits to never cleaning up after yourself! It RIPPED through so so much better than the drill bit. It has to be the skinniest one available so its small enough to fit between the inner tube and outer casing but it made easy work of it.  First one i hammered the shit out of... New method- 20250102_185506.mp4   I did the other 5 in less time than I fluffed around with the first one. With the first couple I used the cut off saw (sawsall as the yanks love to call them) to cut a break in the outer casings. Even with that they're still a prick to hammer or air chisel out.  The last few i just went rambo with the air chisel without cutting them. I over cut one of the early ones so will hit the with the mig to fill the cut then sand it off smooth.  The carnage left over-   I've also been "nesting" ie, cleaning up my babies nursery,  ie cleaning the f**king pig sty of a shed. I've got that much shit laying around it's as cluttered as my head!  Getting things put away, in boxes, on shelves, hanging off walls, all to get some working space back again.  Hopefully that keeps me motivated....
    • AFAIK does the base map for Haltech even have the 4D compensation enabled? It's been a while but when I looked at it I remember it was actually using pure TPS as one load signal and MAP for another. Seemed workable but not ideal by any stretch. A lot of people have "make the event-itis" which leads to stuff like this happening.
×
×
  • Create New...