Jump to content
SAU Community

Rb26dett Head On An Gtt Rb25det Block

TriniGT

By TriniGT,
in Engines & Forced Induction

 Share

Recommended Posts

TriniGT Experienced

TriniGT

Posted
Posted

Alright, this will be my next projec tonce I get my S15 RB26DETT up and running but as for now I am already acquiring some parts, namely the damaged RB26DETT engine. I have done a bit of searching and people are saying that you need to machine the headstud holes and retap, some others also said you can use the RB25DE headstuds and they work proper, can someone clarify. What else needs to be done, was thinking about a new headgasket and a baffle and the usual RB26 headwork for oiling problems. Can anyone advise me who has done it as I am thinking along this direction. If the damaged engine has a good block and crank then my swap will be an RB26 but not sure until it is scrapped, guy just told me it was a spun bearing and the crank needs polishing but no one can know unless it is scrapped. Let me know what is needed as I am thinking along these lines.

discopotato03 Grand Master

discopotato03

Posted
Posted

Good question that , non VVT head on VVT block - if the 26 block is RS .

I suppose you could look for an R32 RB25DE block and fit it with piston oil squirters and good internals .

I think American mobs can sell you non metric threaded fasteners but you have to get the block drilled/threaded and not sure about the heads bolt holes .

Ask SK , cheers A .

  • 3 weeks later...
Adriano Grand Master

Adriano

Posted
Posted

What exactly do you want to know? The head will bolt on using rb25 head bolts, but as i said the compression ratio will be low due to the difference in cylinder volume. You really aren't gaining anything by using a neo bottom end, as a non-neo bottom end will end up with a more appropriate comp ratio. You could get a set of non-neo forged pistons and fit them to the neo bottom end, that will fix the comp issue.

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

Okay are you sure that using the RB25 headbolts I can bolt on the head? The reason I am using the Neo bottom end is because the RB26 engine that I am getting has bottom end damage and that I already have an RB25DET Neo engine in my GTT. Maybe the RB25 forged pistons may be an option I can look at, thanks. I just want to confirm that the headstuds from the RB25 can work on the RB26 head without worries, can you confirm firsthand?

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

I wanted the individual throttles and also the intake mani run on the side for shorter coldside piping, and also maybe do a twin turbo setup all at the same time, oh and the wow factor :/. Actually I am getting the RB26 for a good price and getting aftermarket intake manis for the RB25DET Neo is harder and expensive along with the harder to get injectors and then the exhaust manifold. Okay so RB25DE or is it RB25DET headstuds or are they the same, gonna do a search now?

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

Yes I know but I am getting the entire head for a good price and having the individual throttles is an added bonus as well as the twin turbo setup. Let's not harp on the topic I just want to make sure you can use RB25 headstuds and if so is the RB25DE and DET headstuds the same, I am thinking so. Thanks to all for the input BTW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
    • Radical_Goodspeed
      Potential MAP Reference Point

      By Radical_Goodspeed · Posted

      So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points.  I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC. First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC.  All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference? I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find. Thoughts?
×
×
  • Create New...