Jump to content
SAU Community

Recommended Posts

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

Im sure that the people with oil temp guages in their car will agree with me on this one.

Yep...definitely about 10 mins for the oil to reach anywhere near operating temps(thrashable temps). My drive to work takes 15 mins...I baby it for the 1st third then by that time...I'm in heavy traffic! Oh well...look forward to the weekend to stretch it's legs, for the daily grind, I'll baby her...plus it helps my fuel consumption!

Link to comment
https://www.sau.com.au/forums/topic/24741-warming-up/page/4/#findComment-832720
Share on other sites

  • 1 month later...

Come on fellars, as much as we like to think that a skyline is a super performance machine, at the end of the day, it is a car. In japan, they are our version of commondore. Well, not really, but almost. All this talk about warm idling and taking it easy. Just drive it.

I let my car idle for about a minute. That is start up the car, put my stuff in the car, sit down, and go. Who in their right mind would even think about going a different path just to warm up their car? As a turbo car, it is important to let the oil circulate for a sec to lub the turbo. Then, just go. After the turb is lubed, it is the same as a normal car. Do you see commodore drivers warming up, or circling the block at 40 km/hr to warm it up, or driving on the freeway at 80?

All this analness that you guys are doing will make minimal difference in the end. Might last a few more ks. If you think about it, most likely you may not even have the car in a few years time. Most commondores and other cars last 10-15 years and around 200 000ks. Isn't this enough? in 15 years time r33s will be an absolute shitbox. Would you even wanna be driving it around anymore?

Link to comment
https://www.sau.com.au/forums/topic/24741-warming-up/page/4/#findComment-920558
Share on other sites

Holy resurrect a thread batman!

Why bother washing the car, the paint will be rooted in 10 years' time anyway. It'll be due for new tyres too eventually, so I might as well just torch the crap out of the ones I've got.

I don't see what's so anal about not flogging an engine until it's had time to warm up. I mean really, who in their right mind canes any car when it's stone cold? If you see anyone caning a cold engine, feel free to call them an idiot.

I looked after my VC Commodore no differently than I do the R33, except that the 33 will idle without pumping the throttle for the first couple of minutes :(

Link to comment
https://www.sau.com.au/forums/topic/24741-warming-up/page/4/#findComment-920570
Share on other sites

rev head, you have taken what i said to the extreme. I'm not saying go off and flog it straight away when it's cold. I'm just saying that you should just drive it normal without being all anal about taking it ultra easy in the beginning.

Let me give you an example. Driving it around the block a few times taking it ultra easy. Worrying about going 100 ks/hr after they said that it takes 5 minutes to get there. Thinking about going a longer route.

The difference between driving it normal (say as your parents would) and being ultra anal is minimal.

Link to comment
https://www.sau.com.au/forums/topic/24741-warming-up/page/4/#findComment-920572
Share on other sites

I think it comes down to whatever YOU feel comfortable with. If your happy to drive it soon as it turns over go for it, as others have said probably wont do damage if its babyd for a few minutes. If you prefer to let it sit for a minute fine, not hurting anyone, you couldnt spit more fuel than is being used in that minute either. Personally i let mine sit until i have seatbelt on, windows down or until i feel ready to drive off(minute or so). I believe my car runs better if left to warm up a little, specially on these cold mornings. I know ppl with v8s, skylines etc who will turn there car over in their driveway, walk back inside do this and that then drive it. They swear by it.

Just like those speeding adds, is taking that extra minute to get to your destination really going to make a difference? IMO

Link to comment
https://www.sau.com.au/forums/topic/24741-warming-up/page/4/#findComment-920742
Share on other sites

  • 3 years later...
just out of curiosity, how long on average do you take to warm up your car?

i take at least one cigarette time to warm up (10mins approx), that is when i see the oil temp needle touches the first white line and my rpm sits around 900.

i feel that it's a little long, and it doesn't help when i'm rushing to school. been considering a remote start too.

comments?

p.s i drive an R33 GTST M-spec

My old mans a mechanic, he says this: When a car has first been started and is running at idle the amount of oil flowing around the motor is negligable ie low oil pressure, oil will not reach all areas of the engine correctly until the the oil pump is opporating at revs. Oil pumps reach their maximum pump pressure @3000rpm. You should never exceed 3000rpm until engine temp is at normal operating temp. It is also important to correctly warm down a motor with the final k's done within normal driving operation not thrashing the pants off it. I drove a highly boosted to 16lb Laser Tx3-4WD to 360,000km's on the clock without engine failure by following this advice with regular 5000km oil/filter changes until I sold it and joined the "Legion of Skyline-There can be no other"

Thats my 2c

Start the car up for about 5mins just b4 I goto work. If Iam running late I'll give it atleast 1min or 2 and take off easy. Drive it easy for a good 5 - 10 mins and everything is at normal driving temp.

Also the weather can effect it too. If its a hot day then the car will not need as long to warm up.

Edited by (00)SKYLINE(00)

What an old thread. Im not so sure a general rule of "3kRPM"

I figure, clearences are designed around operating temperature, so keeping it below 3K for 10mins (if theres traffic, in winter conditions) can effect bearing wear. I give it 30-60s then drive keeping under 4'ish. As it warms up, lean on it more.

I start my car, set the turbo timer to 6 mins, go inside and brush my teeth, then jump in my car and by that stage its been on for about 3.5 to 4 mins, then i drive off and go the speed limit till it reaches its normal operating temp. After that if i feel the need to speed i will with a clear conscience.

Edited by WET-25T
  • 1 year later...
I start my car, set the turbo timer to 6 mins, go inside and brush my teeth, then jump in my car and by that stage its been on for about 3.5 to 4 mins, then i drive off and go the speed limit till it reaches its normal operating temp. After that if i feel the need to speed i will with a clear conscience.

EXACTLY what I do... I couldn't believe someone else saying exactly what I was going to!

EXACTLY what I do... I couldn't believe someone else saying exactly what I was going to!

This has been covered 100 times but cant believe it needs to be said. The LONGER your car takes to reach operating oil temp will just do it more damage! You let your car idle there because you think its good for the engine when its not! Jump in, start the car. Put on your seatbelt. Set your radio. Then start driving at low rpm off boost untill it reaches operating temp. Your gearbox oil, diff oil and everything else doesnt get warmed up with your car just sitting there.

This has been covered 100 times but cant believe it needs to be said. The LONGER your car takes to reach operating oil temp will just do it more damage! You let your car idle there because you think its good for the engine when its not! Jump in, start the car. Put on your seatbelt. Set your radio. Then start driving at low rpm off boost untill it reaches operating temp. Your gearbox oil, diff oil and everything else doesnt get warmed up with your car just sitting there.

Agreed. That prob equates to what? 30 seconds?

Lets end the debate there. =)

  • 4 months later...

alright guys i know its a bit overboard but i love my car its my pride and joy and couldnt stand the fact of it wearing away.so this is my daily ritual:

4am, wake up, go to garage drain all the oil in the car inc gearbox.

6am, put all the fluid in the massive pot stick a temp gauge in it and bring up to specified boiling temp.(you wanna get it just a bit over cuz it will cool down a lil b4 puttin it back in2 car)

6.30am, put all fluids back in the car just in time to drive to work.

6.32am have the car sideways out of the driveway with no worries of engine wear

Previous to a service I got a squeak as a belt moved on cool start, and if I accelerated prior to warm up it sounded bad... I normally warm it up for 5 mins or until the oil guage is under that middle line it sits above just after start... doesn't run rich when driving and I have a 100km zone out front so its gotta be ready to go

alright guys i know its a bit overboard but i love my car its my pride and joy and couldnt stand the fact of it wearing away.so this is my daily ritual:

4am, wake up, go to garage drain all the oil in the car inc gearbox.

6am, put all the fluid in the massive pot stick a temp gauge in it and bring up to specified boiling temp.(you wanna get it just a bit over cuz it will cool down a lil b4 puttin it back in2 car)

6.30am, put all fluids back in the car just in time to drive to work.

6.32am have the car sideways out of the driveway with no worries of engine wear

true story?

:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
    • I have a heap that i have collected if you want some authentic ones still. Pm me if your interested!
×
×
  • Create New...