Jump to content
SAU Community

Cusco 1.5 Way Mechanical Lsd

wegs
 Share

Recommended Posts

wegs Collaborator

wegs

Posted
Posted (edited)

Item: This 1.5 way Cusco LSD had only just been installed in my s14 when i bought it 3 months ago. Works great but I'm not making use of it so am changing back to the more subtle nissan LSD.

Details: Not getting any knocking noise people often complain about with mechanicals. Diff has 6 bolt output shafts. Advertised as a whole but willing to remove centre for shipping etc. Pulled the back off last night... everything looks good. Oil was fresh and clean.

Price: $700ono

Contact: PM or reply here

Location: Adelaide, NEast Suburbs

Thanks,

Wegs

post-16206-1228344771_thumb.jpg

Edited by wegs
Link to comment
https://www.sau.com.au/forums/topic/247621-cusco-15-way-mechanical-lsd/
Share on other sites
wegs Collaborator

wegs

Posted
  • Author
Posted
probably a stupid question but will this fit a 32 gtst?

Nah not a stupid question at all. It's an R200 diff... so yes it will bolt into the subframe. But you would run into problems if your skyline has 5 bolt drive shafts and/or ABS. I don't know about the skylines.. but some of the 200sx's had 5 bolt driveshafts and some had 6 bolt driveshafts. You would only know if this is a good option for you by looking at the number of bolts where your driveshafts meet the diff.

This sale is now on hold pending payment.. but i thought you might still benefit from the info above cause it helps if you know what factors to consider when buying a diff.

Cheers

Wegs

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      GTR R34 Limp Mode

      By GTSBoy · Posted

      Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • steven7270
      GTR R34 Limp Mode

      By steven7270 · Posted

      So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Dose Pipe Sutututu
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Dose Pipe Sutututu · Posted

      Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...