Jump to content
SAU Community

Recommended Posts

if this is indeed what youve done, drain some out asap... it will be churning up the oil and aerating it... causing it to be more like whipped cream than pouring cream. it will also pressurise the sump causing more blowby and more oil consumption... being that the turbo runs on bushes, with aerated oil, this will wear causing oil into the turbo, hence you oil dripping from the bottom of the cooler.. and also running rough as the engine tries to burn the amount of oil coming in... fouling the plugs etc.. will happen worse with boost.

it also does wonders the already fragile oil pump as it cavitates away trying to pump the whipped oil.

when it comes to engine oil, or any other fluids, its ok to admit defeat if you dont know what you are doing.. ive had to go over an entire brake system when someone put engine oil the brake fluid in a euro car because they couldnt figure out the picture on the cap...

dont under estimate a simple top up, its too easy to get wrong.

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

dude, you have to completely drain the old oil out before you put the new stuff in.

ie. take care for a drive so oil is warm.

jack up the front. place drip tray under the sump.

take off top oil cap

undo sump plug bolt

let oil drain out the bottom for 10 mins or so

then put sump plug back in

fill up from the top to the appropriate level. each car takes a different amount of oil. make sure you know how much your car needs

replace oil cap.

start car, run for a minute or two.

turn car off and check oil level. top up or drain as needed.

now enjoy.

also, personally I would go with a better oil than turbolight. it's cheap rubbish really. sure it may be 'ok' but there are many better oils out there. if you want something that is actually good, go with motul chrono 300V. very good oil for your skyline to live a long happy life. :)

sump = empty

sump + 5L oil = sump with 5L of oil

sell to new owner

sump = 4L of oil in it (let say it's used/leaked a litre)

sump with 4L oil + new 2L oil = sump with 6L oil

OBVIOUSLY it's going to blow out of where ever it can.

I don't mean to be rude, but how can you get an oil change wrong?

even if you are a ford man.

I'm pretty sure Fords have sumps and hold x amount of oil which you DRAIN via the sump plug before putting new oil in.

For the record, I used Motul 4100 turbolight for over a year on one of my old R32 GTST's.

never had a problem.

it was only a street car.

didn't go to a track or strip and didn't spend any time sideways.

Current skyline is on a diet of Castrol Edge range.

10w40 in winter and 10w60 in summer

I use Turbolite too in my R33.

Dont see what the problem with it is. Using the 300V on a street car is way overkill IMO. Maybe in a highly strung engine its alot better, but in humble old NZ i have to get even Turbolite from Aus, and its not cheap.

I noticed the car runs alot smoother and idles alot quieter with the Turbolite. Apart from the exhaust and fan, the engine is silent. Cant be all bad!

Haha im keen to see a response to this, he's either put 2L on top of the existing 4L or drained it all and only put 2L in

I wonder if he changed the filter?

I find turbolight 10w40 is a bit thin for old engines like ca18 and rb20, especially for drift when its getting hot and thin

Ford or no ford, when you change your oil you drain the old one out first...lol Just ask a mate who is mechanically minded to show you how to do it, that or take it to a mech and get them to show you. Swallow your pride and learn something or else you'll end up killing something like your car.

yeh windage will cause whipped oil. your engine will be A1 ok when you sort the problem out. just drain the WHOLE lot INCLUDING the oil filter cos it can hold about 500ml of shitty aerated oil. replace the oil filter then refill with good oil. personally i use castrol edge. i would also suggets changing the oil again in about 400km (not 4000) just to make sure you have got all the shit oil out. then every 5000k should be great. hope you get it all sorted out soon.

guys not everyone is mech minded..

so i think we should be HELPING our fellow skyline lovers. not laughing at them.....

this is genius reminds me of a mate who saw the dipstick was on low and added 4 litres of oil........just drain it and replace it and for god sake ask someone if u dont know what your doing! it amazing how basic stuff like an oil change can go wrong hahaha

Jeez does reading this thread hurt anyone else's head?

Its probably been said quite a bit now but if your not sure about something dont just have a crack at it and hope for the best as more often that not it wont turn out well.

After reading all the replies to such a simple question, it would be obvious the guy knows his mistake and hopefully is trying to get it sorted. No need to overly laugh at his mishap.

Im sure we all have done something stupid haha.

Anyway, do i see a padlock coming to this thread?

Well thanks to those with helpful information, everything is back to working order, and it seems even better so yay, special thanks to PUDZ your information was spot on and invaluable to getting my baby back her glory, Thanks again

Well thanks to those with helpful information, everything is back to working order, and it seems even better so yay, special thanks to PUDZ your information was spot on and invaluable to getting my baby back her glory, Thanks again

Good to hear its back and working, and don't get put off working on your own car - just make sure you know exactly what is involved when you set out on doing something with the car. There are plenty of FAQs around here and elsewhere on what to do just in case you may not have thought of everything :D

Thanks mate, yeah shall do my research thoroughly next time, will make all the difference lol :( thanks again

What was the problem?

And how did you fix it?

Did you just do another oil change or did you do an engine flush and redo the oil and oil filter again?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • We will review wtf is going on, but if you made any donations let me know and i will follow it up with the admins
    • See, that button sounds like perfection Duncan! My eyes really don't like light shining at them from a dash when I'm driving. Being part red colourblind, I've found for most cars that I can change colours on, I set everything to red, so my eyes see the elast amount of colour! I miss normal gauges in cars
    • bro, knowing the Japanese in  the 90's, i wouldn't be surprised if they shared components across their model lineup.
    • Maaaan so many "little" things  i rly hope my old RB20 would be "ok" and not too bad. I try to learn what and what not do i need. I look at crossmember at it looks different...even parts numbers are different. Wiring and all that i rly do not know...yeah someone mentioned the speedo thing. On that yoke clip. I rly do not know what can and cant be done "custom" so that is why iam asking to know and not be suprised 🙂  I know what it looks like  
    • Oh, there's also the gearbox crossmember which will probably be different between the small box and the big box, and the wiring loom will probably need to be modified, because the plugs for the switches etc, will probably be different. And I think the speedo on the small box R34s is from somwhere stupid, like the diff, possibly, so you'd need to work out what needs to be done about that (assuming it is different). I think the thing you need to realise is that the front end of that yoke is a large hollow tube with splines on the inside that mates with the splines on the box's output shaft. It is a dedicated thing - not available "aftermarket". They were made to suit that box, by the car's OEM.
×
×
  • Create New...