Jump to content
SAU Community

Recommended Posts

fullee sick 20s bro

unless your planning on entering your car into a show (which you very well might be) don't even consider driving around with them on the street.

i'v never understood why you would compromise handling and grip in a sports car for cheap lebo looks.

my mate had 20" vault cyrstals on his R33 gts-t

not only did it look shiit the ride quality was completely fkd.

If anyone noticed alot of cars including the GTR now comes with 20" rims, Several race cars run big 20" on the front to increase handling.

20's will fit get the offset right n work from there.

yes the new GTR comes with 20s. but the gts-t originally came with 16s

i wonder how 24's would go on the new GTR. my guess is not so good.

If anyone noticed alot of cars including the GTR now comes with 20" rims, Several race cars run big 20" on the front to increase handling.

20's will fit get the offset right n work from there.

Those wheels are not chrome bling though.

If anyone noticed alot of cars including the GTR now comes with 20" rims

For looks. The car is so huge that small rims look disproportional.

Several race cars run big 20" on the front to increase handling.

I'm curious to see which race cars do. And I'm not sure how increasing unsprung weight and rotational inertia provides an increase in handling.

Going to big rims has little to do with improving handling, especially not a 4" increase over stock. On a race car you go for the smallest wheels you can fit around your brakes. Sometimes that necessitates putting on bigger rims than stock.

At any rate, the suspension is engineered around the wheel/tyre combo. What's the likelihood that this guy's R32 has its geometry and components engineered around 20's? Or that it will only get driven on smooth surfaces where the loss of sidewall compliance and increase in unsprung weight is not going to more than offset the supposed benefits of reduced sidewall flex?

hey guys i am just wondering if any1 knows whether or not 20" rims will fit a stock r32 gtst (the offsets and width and bolt patten are all proper) or if i will have to raise the car to fit these.

Thanks

as mentioned in the original post the car is stock.

the cars "geometry" has been set up to handle the stock 16" wheels that were issued from the Nissan factory floor.

so 20s will not do at all for this setup.

If anyone noticed alot of cars including the GTR now comes with 20" rims, Several race cars run big 20" on the front to increase handling.

20's will fit get the offset right n work from there.

Ahahahahahahahaha

hahahah

hahahahahaha

hahahahahahaha

haha

hah

ha

Buses come with huge tyres and rims - so by that principle bus wheels should work out OK on the 32 as well.

GOLD.

:)

can you see the rims when your driving?? i cant on my r32 so my guess is no... therefore looks mean nothing, purpose means everything. buy your 20" rims and stick em on your wall, use them for a glass coffee table or tv stand where you can see em.

for the record buses are not 5 stud lol best come back i got.

TO ANSWER THE QUESTION:

Yes they will fit .. you would need a cheese cutter wheel something like 20x8 with an offset to fit .. coilovers would do wonders too ..

Edited by DECIM8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm at the point of seriously starting a project to build and Arduino/mc (of some sort) based multigauge to go in the console where triple gauges normally sit. I have found a screen of the right dimensions. I would need to 3D print a bezel/housing to make it mount up pretty. That's doable. I would need to come up with interfacing circuitry for the EGT thermocouple. I'm sure there will be examples of that into Arduino out there somewhere. Ditto with characterising the output of the existing boost gauge's MAP sensor and the oil T gauge's thermistor. And then, because it is a screen, it can be controllable, so it can show more than the 3 gauges I currently have. So I can come up with a list of other things I want to be able to show on it that can be reasonably easily handled via an Arduino's inputs. I do not need this project. But the stepper gauges I'm using are giving me grief. It's time to come kicking and screaming into the 21st century.
    • Would you really prefer pillar gauges over something like this? https://www.haltech.com/product/ht-067010-haltech-ic-7-digital-dash-kit/ Or if you can spend more, this? https://www.haltech.com/product/ht-068000-haltech-uc-10/ I could write a thesis about how much better a modern dash is compared to a series of gauges. 
    • People think it's a waste of space, ugly, etc, generally associate "emissions control equipment" with "bad". These OBD1 vacuum-only systems I'm not a huge fan because I think they don't go far enough. They're wasting some of the fuel captured because they start purging as soon as the engine pulls vacuum. Later OBD1/OBD2 they put an electric purge valve on them to vent only when closed loop is active so the ECU will trim some fuel out. Even later OBD2 with zero evaporative loss the tank is 100% sealed from atmosphere until you run the engine or press the refuel door release. The tank has to take much higher vacuum/pressure spec but you never deal with saturating the charcoal canister and losing some fuel that way. The fuel also lasts as long as it would in a 100% airtight container which is nice when you're dealing with modern E10 pump gas.
    • If your luck is anything like mine, what happens is in the process of pulling hoses to get access to the one leak you create many more leaks because every o-ring was on the verge of failing and the strain of pulling it apart caused it to fail. Sometimes life is simple, sometimes you pay twice trying to save once. For the R33 you can still get most AC components from Nissan, I use nissan epc data or amayama to look up the part numbers and then search for the cheapest/most practical way of sourcing from there.
    • The dirty secret is there is nothing recyclable about the plastic bag or old plastic bottles either. Our local trash collection explicitly calls it out as hazmat in both cases. Oil-soaked rags + paper towels too. Oil-soaked cardboard is also not recyclable. The most common case of oil-soaked paper like that is pizza boxes, which are explicitly compost-only from the oil. To my knowledge hazmat oil contaminated plastic the only solution is either landfill or "thermal recycling". Most plastics in my experience there is slow permeation of the oil it's holding into the container so it's very challenging to get it 100% clean.
×
×
  • Create New...