Jump to content
SAU Community

Recommended Posts

Guys,

After some opinions on semi slicks. I am going to start running Sprints at QR/Lakeside next year in a R32 GTST. It will be fairly basic just stripped out to reduce weight and a little extra power over standard.

I will run 16" standard rims but will spend some dollars on semi-slicks. I spoke to the Dunlop guy at QR on the weekend and he said about $400 per tyre. I think it is about the same for Bridgestones. I have seen some Toyos on Ebay for around $260.

So the question is how much difference is there in brands assuming all are semi slicks with same sizes?

I can understand that spending big dollars to gain an extra few percent if trying to run at the front of the field but I think I am a bit off that.

Anybody got any other suggestions?

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Guys,

After some opinions on semi slicks. I am going to start running Sprints at QR/Lakeside next year in a R32 GTST. It will be fairly basic just stripped out to reduce weight and a little extra power over standard.

I will run 16" standard rims but will spend some dollars on semi-slicks. I spoke to the Dunlop guy at QR on the weekend and he said about $400 per tyre. I think it is about the same for Bridgestones. I have seen some Toyos on Ebay for around $260.

So the question is how much difference is there in brands assuming all are semi slicks with same sizes?

I can understand that spending big dollars to gain an extra few percent if trying to run at the front of the field but I think I am a bit off that.

Anybody got any other suggestions?

225/50*16 is the control tyre size for the older Saloon cars. They use Kumho V70As now. If you hunt around you may be able to get one of those guys to buy some tyres for you at their discounted price, or get some of their old tyres cheap. Otherwise, try Hornibrook Motorsport the QLD distributor forKumho Motorsport tyres. They may be cheaper anyway due to the higher volume they'd sell compared to other brands.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4306172
Share on other sites

here is where u buy bridgestone RE55s in brisbane

http://www.amecautocare.com.au/bridgestonetyres.htm

the dunlops are said to be just a little gripper, i still sue the re55s as there a little cheaper and still a very very good tires and they heat cycle very well so i can still use them on the street........... they only loose grip once they down the canvas which is awesome.......

i recomend re55 is start with then if u wanna go just that little faster later on buy the dunlops for the extra $150 a tire....

just my opion but, other ppl may have different ones

good luck buddy

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4306376
Share on other sites

just a note.

I purchased 4x 18" 265x35 Re55s recently from Donnellan's in VIC and had them shipped to Brisbane $77each cheaper than the price quoted by Amec...

Make sure you check a couple of prices before buying semis...

Michael

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4306391
Share on other sites

slapper, did you have them buffed? full depth RA1 is only recommended for use as a wet. Hornibrook Motorsport can buff them for you - its not that expensive. They'll go at least a couple of laps longer after buffing and you'll probably get more life out of them too.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307048
Share on other sites

Just be careful what Toyo's you get - avoid the RA-1's, I've got these on my GTST and they are shockers on a hot summer's QR track (only get 1 lap out of them before they turn to marshmellow's). Go the RE55s.

TOYO R888 SEMI SLICK is what is advertised. They don't say what compound.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307050
Share on other sites

I will run 16" standard rims but will spend some dollars on semi-slicks. I spoke to the Dunlop guy at QR on the weekend and he said about $400 per tyre. I think it is about the same for Bridgestones. I have seen some Toyos on Ebay for around $260.

Dunlops are expensive, but I didn't know they were that expensive. I pay that for R888s in 17". My Bridgestone RE55S cost $450 a corner in 17".

The R888s don't grip as well as the Dunlop offerings, but you should be able to get them new from an authorised dealer for $350/corner. They are one of the cheapest semi slicks out there.

I've found the best bang/buck are the Bridgestone RE55S. I'd get Dunlops if I could afford them and am chasing times, though.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307079
Share on other sites

Yeah I don't think there's much doubt that the Dunlop 03G is the fastest tyre at the moment. Be backed to backed them last year with the Kuhmos and they were nearly exactly a second a kay quicker.

I need new rubber for my 32 gts-t and I'm getting O3G's.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307091
Share on other sites

I was looking at putting R88s on my GT-R and ended up going with R1Rs - haven't got them on yet so I can't give you a definitive answer about their performance.

When I was researching, I spoke to a rep who suggested the R1Rs over the R888s, firstly because they obviously wear a lot better (think about the percentage of time you'll spend on the street) and also, being a newer design than the 888, has grip levels approaching the 888 without being so reliant on buffing or having good temp in them for max grip. Worth thinking about if you're not planning to be at the pointy end straight away.

I suspect you'll find the 888s on eBay are parallel imports, and GGG compound rather than GG. Naturally Toyo are going to protect their turf, but this PDF does have some valid points.

http://www.toyo.com.au/RacePDFs/Bulletin%2...oxes%20R888.pdf

Edited by Iron Chef
Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307195
Share on other sites

Are those 888's on ebay from st george tyres?

I used them before, was happy, got quite a few days out of them, but need new tyres asap also

Yeah they were from St George. checked online again today and they are only listing one size now. 225-40-18 $1450 a set.

they also are advertising Falken RT615 in various sizes. they are even cheaper.

Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4307551
Share on other sites

they also are advertising Falken RT615 in various sizes. they are even cheaper.

That's because Falken RT615s aren't an R-Compound tyre. They won't grip anywhere near as well as the R-Comps everyone else is suggesting, nor will they last as long before overheating.

The RT615s are not a proper circuit tyre. In a motorsport setting, I wouldn't consider them for anything other than a wet weather tyre or a hillclimb tyre.

Edited by scathing
Link to comment
https://www.sau.com.au/forums/topic/248107-semi-slicks/#findComment-4309280
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
    • yep just a JIC vs ISO insulator height. old coils are for JIC, new coils are for ISO
×
×
  • Create New...