Jump to content
SAU Community

Recommended Posts

I'm having a few issues with my 32.

Current mods are 3" cat-back, aftermarket coils and FMIC.

The stock turbo seems to have an aftermarket actuator on it running at 14psi.

The turbo ramps up to full boost fine and holds it without a problem, but once at full boost, the 32 seems to loose power. It doesn't cough or hesitate, but seems to plateu torque wise. A couple of worthy side notes, there seems to be a feint squeeling coming from somewhere on full boost, I was thinking belts slipping, but could this be a shagged turbo? Also the IC is slightly damages on the bottom, but doesn't seem to leak.

I have checked for boost leaks (though it wouldn't hold boost if it did have leaks) and changed the fuel filter. Next on the list is plugs.

I was thinking:

* Ignition timing

* Fuel pump

* Exhaust manifold gaskets

* Blocked cat

Any other thoughts?

Link to comment
https://www.sau.com.au/forums/topic/248317-32-gts-t-problems/
Share on other sites

have you checked all the vacuum hoses to boost controller, checked the coolerpiping and just all the hoses n stuff around the engine bay?

little squeeling suggest your losing boost pressure somewhere via a hose or pipe, as its only small.

just food for thought...

have you checked all the vacuum hoses to boost controller, checked the coolerpiping and just all the hoses n stuff around the engine bay?

little squeeling suggest your losing boost pressure somewhere via a hose or pipe, as its only small.

just food for thought...

I checked all the vac hoses tonight, and am not running a boost controller.

I was thinking the same thing about the squeeling, but thoughts because its holding pressure (acording to the boost gauge) I kinda ruled it out.

put it on a dyno and check your a/f r's...mine did the same,car was running out of fuel

My AF gauge (though dodgy) is leaning out under boost, would this indicate fuel pump? What was the reason for yours running out of fuel?

Have you considered that the ECU isn't programmed to run the engine with 14psi boost behind it?

I have, from what i've read, the factory ECU can handle it fine... though I havn't pulled it out to see if its been fiddled with...

Well, I spent the afternoon at the workshop, changed all 3 belts, the squeeling has gone altogether, cleaned out the AFM and airfilter (KN drop in panel) its now running 100% better but still hesitates/misses above 5000rpm on boost.

I'm changing out my plugs and IC core (as mine is slightly damaged) on Saturday as well as looking at a new fuel pump.

Will let you know how I go.

Just a side note, when cold, I have to sit in the car when I start it and hold the throttle slightly on for a few seconds otherwise is stalls.

Hmmmm

Well, after a long weekend, I've finally gopt the 32 running at 99%

Changed the plugs (turns out the ones in there were the wrong ones for the car!)

Got the injectors cleaned

GTR fuel pump

New turbo actuator

Runs beautifully now, but still coughs and hesitates when cold.

Going to be checking the ICV tonight.

Thanks all for the help.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had never actually looked into it, but aren't onboard compressors a thing in trucks?
    • Read the ECU for fault codes or have someone else do it. A faulty coolant temperature sender is usually listed in ECUs. If the sensor itself is not busted it can also be a bad ground connection. Or in a really unlucky case, damaged wiring.
    • Can't be a Futjitsubo as those are made with a flex piece and Reimax is smaller in pipe diameter. If anything it is closest to a Mines pipe, but evidently it is not an actual Mines pipe.   Classic word humor
    • Alright I will try to not forget.   As GTSboy replied to you already, problem is mainly the mismatch between the actual exhaust part and the denomination in the papers. That basically just looks like tampering to a cop, if they were to check your car and notice. If it had been done right they would have clarified it to be a custom pipe and just given it a certain part number that you have to engrave or weld onto the pipe. I will definitely inquire on what to do. Changing the pipe wouldn't be my favorite solution as it costs a bunch of money and the cat was fitted with the front pipe and exhaust under the car, and if the front pipe flange does not sit in the OEM location the cat will need to be refit for any other pipe to work. It also usually doesn't need a brand name or something like that, but more something like a part number. Usually for exhaust parts, on silencers and cat units specifically, there is a badge that reads the certificate number that belongs to these exhaust parts under EU regulation. You get these numbers after you put a part or group of parts through the tedious testing according to EU vehicle legislation and they pass. You can find these "part numbers" on various parts throughout a EU vehicle. On windows, headlights, engine parts, seat belts and so on. All these parts have gone through standardized testing and acquired a so called ECE or EG Certificate that makes them legal to use by themselves in all countries that adhere to these standards. You can also not alter these parts in any way, if you do they become illegal. An example for stampings on an exterior lighting part, the people who need to know can find the documentation for this unit in a database. I do not know what all the standards and so on mean.
    • If that was the case I suppose you could call it "Mein's" brand....  ... I'll see myself out... 😅
×
×
  • Create New...