Jump to content
SAU Community

Taking Off Gtt R34 Front Bumper

viet_boi

By viet_boi,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

Charles89 Grand Master

Charles89

Posted
Posted
My inner plastic guard is basically stopping me from getting to the screws holding the front bar on near the tyres.

I can' t even get a finger through let alone a screw driver. Any tips for 34 GTR or is it different to GTT as far as removal technique?

There's like 3 screws underneath your front bumper holding onto the mud guard, and a couple along the front fender, after undoing those, you should be able to pull the mud guard open a little, just enough to undo the 2 screws holding onto the front bar.

Worse comes to worse, just completely take off the mud guards and leave it off :P

  • 1 month later...
V28VX37 Veteran

V28VX37

Posted
Posted

Thanks heaps for the tutorial viet_boi! Clear and easy to follow, just take your time if you haven't done it before.

... you could take the cover off (Plastic surrounds around the front wheel) there's only couple plastic screws holding it in, 2 on the bottom and 2 in the guards from memory, as soon as you take that off getting to that middle screw will be and ease and you wont have to squeeze in, this takes longer to take off the front bumper and more things to put back on.

My inner plastic guard is basically stopping me from getting to the screws holding the front bar on near the tyres.

I can' t even get a finger through let alone a screw driver. Any tips for 34 GTR or is it different to GTT as far as removal technique?

I definitely recommend loosening the plastic guards first, getting to the two front bar side bolts is heaps easier then. Just pop out the plastic clip in the middle of the guard and that should allow you to get through to the bolts. If not, there's another clip further back down low that you can remove, too. I also had to turns the front wheels away from the side I was undoing to get some clearance.

just took mine off, one thing i came accross if your front bar hasnt been off before there will be 10x 10mm screws holding on the plastic mud guard thingos running the full length of the bar. :(

Be careful with these, I had a rusted one that I tried to force, which ripped the whole metal clip with the nut off the front bar... Get the easy ones off first and then put a spanner through to hold on to the nut for the tough ones.

And remember, this is the easy part of the intercooler install :)

  • 4 weeks later...
theponyremark Proficient

theponyremark

Posted
Posted

Sort of related but rear bar. I have removed my rear bar and got a Bomex rear bar. Do I re-use the two metal rail mounts from the stock bar? The Bomex has nothing on the sides to mount it on...

  • 6 months later...
blah_blah Grand Master

blah_blah

Posted
Posted

Thanks for this did this on the weekend,

Apart from the screws in the inner guards being a bitch to get to and some of my screws under the front bumper rusted to the point where it just broke off all went well lol :thumbsup:

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PLYNX
      R32 GTS (RB20DE) clogged cat

      By PLYNX · Posted

      Oh bugger ! Your right ! Good old hydrogen sulfide. Takes me back to the good old school days ! 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I've owned a few scooters over the years, a Vespa PX oil burner was my first scooter, followed by a few others, including a little 50cc BeeWee that I used as a barracks bike, and I've had a blast on all of them, they really are the cheapest for of city/suburb transport around The only issue with scooters in Australia is lots of people look down on them due to their size,  maybe they need a big bike to make up for something else where they are lacking, unlike Europe and Asia where every man an their dog owns one, and now that filtering is legal in NSW, local traffic is never a issue Not to say I haven't owned my share of big cc bikes over the years, but they were for more blasting through the hills or Hwy riding where it needed to sit on Hwy speeds Safety wise, I ride like everyone is always trying to kill me, everyone is running a red, or running stop/give way signs, or generally asleep at the wheel, which most people are duringtheir commute, I also ride really safe, and give myself, and everyone else enough room in case I need to pull some hasty evasive actions, I've done a few rider training days over the years, which has come in handy on more than a few occasions  As for mods, there's nothing really, and yes your right about aftermarket exhaust, all you get is loud and obnoxious noises from them, like every 250-300 cc you hear with a aftermarket muffler, in saying this I did put a rear muffler from a 125 Aprilla on one of my old 125 scooters, it was horrendous and no amount of full face helmet and ear plugs would dampen that noise As for coming from the Harley, and what a overpriced POS that was, I no longer do big rides as my poor old busted joints ache after about 1/2 an hour of riding, long cruises are so much more enjoyable now in a car, so a big bike would be pointless   
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      Oh wow, it's easy to forget how cheap these can be. Probably the cheapest way to travel. Though people in cars here tend to be morons and I would not feel very safe. Were scooters ever big in Australia? It used to be the thing growing up in Europe ~20 years ago. 50/70/125ccm Peugeot or Yamaha and some others. Utterly obnoxious Polini race exhausts. Kick stands that slant as much as possible. So loud. So much noise for really not moving very fast at all. But it felt cool at the time. Not sure where I'm going with this, but there is an aftermarket for mopeds! Though I'd have pictured you more for a Goldwing kind of guy after growing out of the Harley.
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      You need to know I am sorry for this.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      As the MX5 isn't apparently "manly" enough, and I need something for runs to the local shops, and also take to my part time job at the salon, basically I can keep the MX5 away from car parks and stuff......like "flying lockers", I was wondering what I could buy to fix this issue LOL, I pick up a new Yamaha 125 Delight this arvo from Trooper Lu, basically a R1 that you can fit a slab of beer on between your feet, also, it was $29400 cheaper than a R1, so actually it's 2 x better than a R1    
×
×
  • Create New...